[SOLVED] pic16f72 sinewave inverter with asm codes. not working.

Status
Not open for further replies.

This code is for MULTIPLICATION,

;**** Define a macro for adding & right shifting **
;Macro
MULT MACRO BIT ;MACRO FOR UNSIGNED MULTIPLICATION
btfsc mulplr,BIT
addwf RESULT_MSB,F
RRF RESULT_MSB,F
RRF RESULT_LSB,F
ENDM ;END OF MACRO FOR MULTIPLICATION
 

Attachments

  • Matrix.jpg
    223.9 KB · Views: 399
Last edited:

well i build this inverter and it works fine on 24v but it doesn't work well with 12v because the maximum output voltage obtain is 170volt ac 50 hz with 12v but it works fine with 24v and i am thinking the problem might be from the code can someone look into it and reply please.
 

OBIALOR said:
All i am saying is in real life i have connected the ac sense transformer to main the beep comes on,but no output from all the osc outputs
Click to expand...

i have build 12v dc input, 220vac output & it works very very fine, to help u what is the voltage at pin 4.

- - - Updated - - -

OBIALOR said:
All i am saying is in real life i have connected the ac sense transformer to main the beep comes on,but no output from all the osc outputs
Click to expand...

i have build 12v dc input, 220vac output & it works very very fine, to help u what is the voltage at pin 4.

- - - Updated - - -

i have build 12v dc 220vac output & it work fine, for me to help u, what is the at pin 4.
 

fmtech i am happy for your effort to help , i have corrected the error .
 

@ ABIALOR have you try it with 12v because it work fine with 24v but even if you try using 6v to 230v transformer it doesn't affect the output voltage.

- - - Updated - - -

masud58 said:
its not a code problem. rebuild your transformer.
Click to expand...

it's not a transformer issue because even if i used 6v -230 it doesn't change anything the voltage can go beyond 170v with 12 volt and even when you connect your feed back it drop the voltage to 130v with 100watt load
 

because it work fine with 24v but even if you try using 6v to 230v transformer it doesn't affect the output voltage.
Click to expand...
It proves problem not lies in code.
I checked in hardware with 12v battery till 500 watts it is working fine.
I adjust output volts 210, till 500 watts these volts become 200v.
And result is satisfactory.
 
Last edited:

Thanks for the reply pnjbtr but what do you think we be the problem why the voltage doesn't go beyond 170v
 

Thanks for the reply pnjbtr but what do you think we be the problem why the voltage doesn't go beyond 170v
Click to expand...
I think,most chances are that your transformer,s feed back(15V) volts are not ok.
If you are sure that transformer winding is perfect.
Then check these components,R44,R45,VR1,C10 and diodes D12 to D15 and D16.
 
ok i finally solve the problem,now it works with 12v fine thanks for pnjbtr
 

hiiii everybody im thinking to make this inverter i changed the pwm frequency from 3.5Khz to 7.5Khz i attaced the hex code can any one try this code??

second question this is a 500watt designe but i want to convert in to 1000 or 1500 watt (24V) what i have to change?? in the code how can i overload cuttoff setting and increase the load please help

i also have this code for pic16f73 with 7.5Khz pwm frequency and upgraded sine table
 

Attachments

  • default.rar
    3.4 KB · Views: 620

THANKS VERY MUCH BUT ARE YOU NOTICED ONE THING IN POWER STAGE CIRCUT ??? THE PWM OUTPUTS (OSC1, OSC2, OSC3, OSC4) IN POWER STAGE THE PIN SETTING IS PHASE 1: (OSC4 HIGH SIDE AND OSC2 LOW SIDE) PHASE 2: (OSC3 HIGH SIDE AND OSC1 LOW SIDE) WITH THIS SETTING INVERTER NOT WORK!!! BECAUSE I SIMULATED IT WITH PROTESUS CORRECT PIN SETTING IS: PHASE 1: (OSC4 HIGH SIDE AND OSC1 LOW SIDE) PHASE 2: (OSC3 HIGH SIDE AND OSC2 LOW SIDE) SORRY FOR MY BAD ENGLISH

https://obrazki.elektroda.pl/1745541600_1365251173.png

pnjbtr said:
U6 (LM317) can regulate up to 36 v dc.
Just change value of R 71 and get 12v at pin 2 of LM 317.
Click to expand...
 

WITH THIS SETTING INVERTER NOT WORK!!! BECAUSE I SIMULATED IT WITH PROTESUS CORRECT PIN SETTING IS: PHASE 1: (OSC4 HIGH SIDE AND OSC1 LOW SIDE) PHASE 2: (OSC3 HIGH SIDE AND OSC2 LOW
Click to expand...
I test this circuit with pcb provided by MRAHMAN.
Inverter section is working fine, and battery charging algorithm is not satisfactory.
For 24v we need to change value of bat sense resistors R47= 5k5, R48=1k
 

WHAT DO YOU THINK WITH MY HEX CODE (7.5Khz PWM) CHANGE ANYTHING???
pnjbtr said:
I test this circuit with pcb provided by MRAHMAN.
Inverter section is working fine, and battery charging algorithm is not satisfactory.
For 24v we need to change value of bat sense resistors R47= 5k5, R48=1k
Click to expand...
 

WHAT DO YOU THINK WITH MY HEX CODE (7.5Khz PWM) CHANGE ANYTHING???
Click to expand...
I test pwm frequency in proteus is 7.6khz, (inverter mode).
 

YES THANKS, BUT 7.6Khz IS BETTER THAN 3.6Khz??? THIS CAN IMPROVE SOMETHING??
Click to expand...
With higher pwm frequency, there will be no noise of transformer( a human can not listen that noise).
 
Last edited:

Status
Not open for further replies.

Similar threads

Menu
Log in
Register
Cookies are required to use this site. You must accept them to continue using the site. Learn more…