If anybody need help in EAGLE, ask me in this POST !

[confini]

cadsoft eagle clearance error

I didn't FOLLOW it, but I read it and I don't see anything wrong, it is basically the same of what I do for my gerbers.

I will try to check better later, but where is that you "stop"?

anyway just today hackaday come out with another tutorial for gerber generation in eagle:

https://hackaday.com/2009/01/15/how-to-prepare-your-eagle-designs-for-manufacture/

let me know if the result is better!

C

 

[me_guitarist]

eagle rotate 45 schematic

ORIGINAL: C

I didn't FOLLOW it, but I read it and I don't see anything wrong, it is basically the same of what I do for my gerbers.

I will try to check better later, but where is that you "stop"?

anyway just today hackaday come out with another tutorial for gerber generation in eagle:

https://hackaday.com/2009/01/15/how-to-prepare-your-eagle-designs-for-manufacture/

let me know if the result is better!

This tutorial was great & I've successfully output the gerber.
Thank you very much for yr assist.

 

[ricky007]

eagle layout drl

please say how to take printout in correct measurement in eagle without any variation and how to take legend side of the layout .

 

[Old Nick]

eagle ulp modify grid

Hi SyNTaXer;
How can I delete extra sheet from my schematic?
Thanks.

click on the drop-down box to chose which sheet you're on, and there's an option to delete. It will delete the current sheet.

 

[si14]

pcb design cross hatch solid hatch

Hi,
I know this is not the place, but I wonder if someone could help me out. I want to export a design from autocad to protel. but the arc shapes are empty. The borders are fine but the inner area is empty. Does anyone know where's the problem?

 

[confini]

pcb dimension measurement in eagle

I think this is not the right place (see thread title, "If anybody need help in EAGLE...")

try to post it in the "upper level" of the forum (PCB Routing & Schematic Layout software & Simulation) outside this thread

hope this helps

C

 

[timwhunt]

seting up eagle autoroute 4 layer

NEW QUESTION:

Hi, I'm creating my first design for a DIY home etched ONE-SIDED pcb. I have a few places where I just cannot route a connection in one layer, so I need to create a wire "jump" from one spot on the board to another. I can (and have started to) create a simple device with two pads that I'll connect with a wire on the component side (a zero ohm resistor). However, I have to add this "fake" part to the schematic as well, and it just seems like a hack. Is there a better way in Eagle (5.4) to create such a jump in a one-layer pcb design?

Thanks!
Tim

 

[M!k]

eagle library pic18f4620

Route it as 2-layer board and just use one layer. So routing a wire is just a jump to the other layer and back. This way no fake devices are needed in the schematic.

 

[yohann]

eagle cad invoke

Hi SyNTaXer

can you write a ULP that can convert cadence netlist (.cir) to EAGLE netlist.
tnx:?:

 

[cllow2020]

eagle hide invoked pin

Hello SyNTaXer,
...you want only isolate milling (hope it is right translated from german: isolationsfräsen)
....
bye SyNTaXer

Hello SyNTaXer,
after run outlines.ulp the test.out files use what program to view ? are there G-code or image files ??

 

[nford]

eagle cadsoft rj11

Hi,

Is it possible to specify that certain vias are covered with soldermask, and others are not covered before creating Gerbers?

Thanks

 

[cllow2020]

how to panelize in eagle cad

anyone who have using PCB-gcode for router/milling using eagle Free Gcode plugin ULP ?

**broken link removed**

any tutorial ??

 

[jaineshshah]

db9 eagle cad

hi i am currently doing project on microcontrollers for that i have layout in positive form .i want to invert this as i need negative to give in my college
can you help me how to do this in eagle
pls reply fast as i have very little time
my email id is jaineshshah_88@yahoo.co.in

 

[krazeebee]

eagle cad panelize

Hi,I'm newbies for eagle and I want to merge eagle pcb in one board. Now I've 4 board and i want to put every board in one board.please help me Thank you.

 

[noether]

eagle pcb hide ground

Question:

Hellos, how can i copy components from one sheet to another sheet?

EAGLE says "buffer is empty" after doing the copy command on a group or single component.

I want to copy the same schematic many times with little variations in each sheet... and i don't want to redo it everytime xD

Thanks.

 

[M!k]

eagle tutorial ground and vcc

... after doing the copy command on a group or single component.

You've to cut it, not copy it. Don't worry, "cut" doesn't delete anything. I've to admit that this is a little bit confusing in Eagle ....

 

[Analyzer]

eagle to pcad converter

Hi,
This is exactly what i am looking for! I also want to copy a schematic and board to another board. For example i draw a power section with 7805 and its components, now i would like to combine this section with another drawing. How to do that *NOT* to mess up board and schematic drawing?
I open my 7805 board with Eagle and i open another eagle and open my other board. I click on GROUP command and select all 7805 section then press CUT. Then i switch to other board and click on PASTE command. It says Buffer is Empty. So what should i do? Could you tell me please "Step by Step" ??? TIA

Analyzer

 

[javi.ar]

jack input eagle cad symbol

Hi I am running eagle v5.xx freeware and I would like to know if there is any chance to place SMD 0 ohm as jumper in order to avoid wire jumpers, directly into the board so I do not contaminate the schematics.
Thanks a lot

 

[nlksg]

eagle pcb adding thermals

Hi All,

Please Help!!

I want to create pad array in eagle. Half of the board area want to use as prototyping area with pad array. Is there any way to create the array easily?

Regards,
nlksg

 

[mvs sarma]

turning off signal lines eagle cad

Many people seek help in Eagle's ability to print a NEGATIVE (not mirror or image) without third party software?

Is that possible SyNTaXer ?
regards
Sarma