[SOLVED] Op-Amp Positive Supply drops down..........

Status
Not open for further replies.
Kam1787,
Trancation means limiting digits or signal value up to certain level & then above which it will not pass but,in our case while observing signal on CRO Op-Amp Signal displays lifted by 3.58V with respect to ground(which is center tapped point of the transformer).
So shall i need to change resistor ground at input of Op-Amp,as shown in above attached file?
XR2206 Supply Connection is +15V & ground so it is the stage where the signal is lifted?

Thanks,:smile:
 
Last edited:

kam1787,
That was typing mistake but i mean to say Truncation.
Can you please explain me the technical aspect of Op-Amp Output signal been truncated,as from technical term point of view i don't know the meaning?

Thanks,:smile:
 

Dear All,
Thanks 2 all of u:smile:
i got the problem which was related to Op-Amp positive feedback Summing Op-Amp as the corrected signal was again feed to Non-Inverting Terminal as per diagram which was driving Summing Output to Positive Saturation.
So i now modified the circuit and use Inverting Terminal as a feedback which maintain changes of open loop.:smile:

Thanks,:smile::smile:
 

Dear All,
what to do with unused three opamp form TL074 of which single Opamp is being used as an comparator?
Positive Supply : +15V
Negative Supply : -15V


Thanks & waiting for knowledge enhancement,:smile:
 

My personal preference is wiring each unused FET OP as unity gain buffer with non-inverting input connected to circuit ground.
 

FvM,
Non-Inverting Pin to ground,Inverting pin to output pin of opamp,but output pin of opamp will be remain unconnect?
How to connect remaining,



Thanks & waiting for knowledge enhancement,:smile:
 

Attachments

  • OPAMP.jpg
    142.4 KB · Views: 77
  • Opamp.pdf
    130.9 KB · Views: 75
Last edited:

FvM,
I connected unused Op-Amp as unity gain(Post No :26,27) but,still 7915 & TL074 is getting heat up?



Thanks & waiting for knowledge enhancement,:smile:
 

Dear All,
As i mention earlier i have being using TL074 Quad Op-Amp stages wise as mention below,
1-Difference Op-Amp
2-Inverting Op-Amp Gain 0.1(Attunator)
3-Summing Non-Inverting Op-Amp
4-Comparator for Sinewave & Triangular wave as an input,
But comparator output is not responding fast as tr=0.1us mention in datasheet?

Can Tl074 be use as an comparator?

Op-Amp Supply=+-15V,
Sinewave=2.5Vpeak
Triangular Wave=3Vpeak
Carrier Frequency =10KHz,
Comparator Output =+-15 which is max will it create problem?

What will be the alternate good option for comparator?

Thanks & waiting for knowledge enhancement,:smile:
 

4-Comparator for Sinewave & Triangular wave as an input,
But comparator output is not responding fast as tr=0.1us mention in datasheet?
Click to expand...
I fear your datasheet literature is rather randomly. I guess you are referring to the small signal rise time specification, shown for a 20 mV voltage step. For large signal, the slew-rate specification will dominate the rise time. You can expect about 2 µs for +/- 15V supply.
 
FvM,
can you suggest me some Comparator because i also need high slew rate around 20V/us,
i selected below Op-Amp can you guide me which is proper,
OPA354
LM311N
OPA2365


How calculated 2us?
Practicaly i observed Comparator output (TL074) shows 8us change of state time which miss many instances,it is not fast reacting?

Can 10KHz & 50Hz Signal as an input for comparator creates problem because of different frequency,shall i need to have ac capacitor?

I have another dought if +Vsat=5V & -Vsat=0V Grounded,for comparator & Sinewave=2.5Vpeak,Triangular=3Vpeak are given as an input then can comparator work?

Thanks & waiting for knowledge enhancement,

- - - Updated - - -

k i got i think so 8V/us means for 15V it will be 2us,is it ?
 
Last edited:

You should use a dedicated comparator when you want high slew rate and fast reaction. LM311 is an old but still suitable devive. It's output stage is different from a standard OP, refer to the datasheet suggestions how to use it.

I don't know where you see 8 µs delay with TL074, but you didn't show the actual circuit, isn't it? If TL74 is supplied with +/15 V, the output swing is about 30V however.
 
FvM,
I got LM339 which is quad Comparator & i am getting the proper response at the output of Comparator,but what to do with remaining three internal comparator as i am going to use only single comparator from quad?
I searched online many people are suggesting to ground the both inputs of remaining Comparator,will it works?
As for LM311 i was confused with strobe & balance pin,didn't know where to connect the pin?

thanks & waiting for knowledge enhancement,
 

Status
Not open for further replies.

Similar threads

Menu
Log in
Register
Cookies are required to use this site. You must accept them to continue using the site. Learn more…