Problem with USB to rs 232 converter as the device is not recognized

[pradeep23]

hi everyone i am doing one simple project using the following link circuit


https://www.electroniq.net/files/other/ft232-adapter.jpg


i designed the board and if i connect the board its showing some like unknown device.....

I install the driver from FTDIchip.com but there is some can any one help me.......

 

[tpetar]

Re: USB to rs 232 converter

See this :

 

[pradeep23]

Re: USB to rs 232 converter

in my circuit anything is wrong?

 

[tpetar]

Re: USB to rs 232 converter

Circuit what I posted works 100%.

What voltage did you put on VCC, did you measure ?

What L you use on USB pin 1 ?

i designed the board and if i connect the board its showing some like unknown device.....

Definitely is problem on USB side. Did you try on other PC, maybe you have problem in OS, maybe there is trojan party on hard disk in folders ?

Try on some other USB port on PC, try also on other PC, some PCs have very bad PSU and very bad USB voltage.

 

[pradeep23]

Re: USB to rs 232 converter

from pin no 1 3.5v is coming....yes i tried to another pc also but same result its showing unknown device only .......

what should i do for that ....

- - - Updated - - -

i am using windows xp ...... may i know what driver to install for dat?

 

[tpetar]

Re: USB to rs 232 converter

What is IC name precisely, what suffix have ?

Drivers location :

https://www.ftdichip.com/Drivers/D2XX.htm

Watch what winXP you have 32-bit or 64-bit and use adequate driver.

 

[pradeep23]

Re: USB to rs 232 converter

our ic ic name FR232RL ftdi chip.....and i am using 32 bit computer ...i download that driver software from dat website sir 2.06.00 version i download in dat it will show in command prompt installing drivers thats it ......after i connect the board also same result .....anything to change for that............or what to do

 

[tpetar]

Connect device to USB and when he say unknown device, go to device manager, and try to manualy point to driver in installed folder.

 

[pradeep23]

same result only no changes in dat .....may be driver installation problem or what....?

- - - Updated - - -

if i uninstall the device and again scan for hardware changes it will show usb device found and suddenly it will go off....... what will be the problem...............

 

[tpetar]

Generaly you make some mistake about driver installation.

Lets try with this :

Application Note AN_104 FTDI Drivers Installation guide for Windows XP
https://www.ftdichip.com/Support/Do...stallation_Guide_for_WindowsXP(FT_000093).pdf

 

[pradeep23]

what is that CDM driver sir....

- - - Updated - - -

i am using windows xp version 2002 service pack 3...... sir any problem in that...

- - - Updated - - -

please help us we can get driver correctly what to do i FTDIchip.com which one have to download for windows xp version 2002 service pack 3.....

please tell me what to do for installing drivers.............

 

[tpetar]

I give you in post #10 complete guide how to install driver on WinXP, earlier in post #6 I give you exact link for drivers.

 

[pradeep23]

i download the driver for xp sir but its not working........same unknown device is coming sir

- - - Updated - - -

hello sir how to check the PID & VID sir ..........of chip ft232r sir

 

[tpetar]

Device manager / Device Properties / Details Tab.

 

[pradeep23]

if i connect the device its showing like this device enumeration failed .....

 

[tpetar]

Check circuit of device, specially check on USB connector, check again existing connections, replace usb cable.

You make somewhere mistake, this should work like charm.

or

Maybe that IC is bad.

 

[pradeep23]

for dat ic how can i check the pid and vid ............

one doubt if i connect the device it have to show the PID and vid writ...........

how can i check the IC der s any way to find the chip is correct or wrong............