Microwave Oven Door Perimeter Seal

Status
Not open for further replies.
T

Tractor Beam

Newbie level 4
Joined
Dec 8, 2011
Messages
6
Helped
0
Reputation
0
Reaction score
0
Trophy points
1,281
Visit site
Activity points
1,368
On the microwave oven door itself, on the inside of the door around the perimeter there are a number of cavities. You must pop off a removable plastic cover inside the door to see them.

The cavities are formed from a bunch of bent tabs 3/4 inch wide, 3/4 inch deep, and are spaced every 3/8 inch apart. My oven door has about 40 of these bent tabs.

I assume these have something to do with keeping the microwaves from leaking out through the cracks around the door. With my brief experience with microwave guides I found that it was very difficult to keep them in my home made guides. All the seals between two wave guides would have to be machined very flat and the bolts would have to be well tightened. Even very small gaps would leak a large amount of power. The edge seal around the door on a microwave is no where near this quality of seal yet it still works very well.

What I would like to know is: how do these cavities prevent the microwaves from leaking out. What makes them work?
 

The cavities are quarter wavelength deep. They have a short circuit at the bottom, so they reflect an open circuit back to the door frame. Open circuit, no current, no current, no power!
Wave guides normally have a groove on their mating flanges to do the same thing.
Frank
 

Tractor Beam said:
All the seals between two wave guides would have to be machined very flat and the bolts would have to be well tightened.
Click to expand...

As Frank hinted at ..... doing waveguide joints correctly, you would NEVER mate 2 flat flange surfaces. it WILL leak
you also wouldn't two choke flanges

one flange must have the 1/4 wave slot/groove in it these are called choke flanges



cheers
Dave
 



All wrong, gentlemen! The chokes are half-wave long as the required effect is to create a perfect short at the door (and waveguide) gap.
A quarter-wave shorted section of a line creates "open" or a high-impedance effect across the gap.

The half-wave length is not only the choke depth, it includes another length to the gap at the door-frame, to reflect any "leak" back to oven cavity.

Most oven doors do not leak at all if the hinges are not worn. You can detect strong leaks around knobs, power cable and lamp door. Ovens with foil keyboards almost do not leak.
 
A ferrite bar in a nylon or fiberglass+ neoprene sleeve becomes the strong lossy RF absorber on the door seal or on both sides around the edge to attract and absorb the stray energy. Half wave choke provides best path for leakage to follow and get absorbed locally rather than radiate out the slot antenna.

The Ferrite for microwave unlike for SMPS is low mu and very conductive (but lossy) with metal particles which also helps conduct any heat evenly and overall makes the design very tolerant to small gaps.
 

jiripolivka said:
All wrong, gentlemen! The chokes are half-wave long as the required effect is to create a perfect short at the door (and waveguide) gap.
A quarter-wave shorted section of a line creates "open" or a high-impedance effect across the gap.
Click to expand...

I take back my apology ... @jiripolivka you are the one who is wrong
here are 3 listed links to microwave flange info stating that Frank and I were correct

you really had me second guessing myself needlessly
Maybe you need to do a little revision ;-)

cheers
Dave


Engineers' Handbook of Industrial Microwave Heating

https://books.google.com.au/books?i...f choke slots on a waveguide flange ?&f=false


https://www.radartutorial.eu/03.linetheory/tl13.en.html


https://www.rfcafe.com/references/electrical/NEETS-Modules/NEETS-Module-11-1-31-1-40.htm

Navy Electricity and Electronics Training Series (NEETS)
Module 11—Microwave Principles
Chapter 1: Pages 1-31 through 1-40
 


Dear Dave and others:

Please learn transmission line basics:As I wrote, the idea of a perfect short at the gap between the door and frame , and between waveguide flanges , is based on a shorted half-wave section. That the groove is not exactly a halfwave deep is not important. The complete way from the groove end (a short) to the door-frame gap must be half-wave long.
 

The discussion became a bit unfriendly last week so that moderators felt compelled to close it for a while. Hopefully we can clear the open questions now.

I was asked in a mail

jiripolivka emphasized that the choked waveguide flanges implement 1/2 wave (short-to-short) transformation. So what's the role of 1/4 wave dimension in this designs?

I think, the picture shown below (from my favourite German Taschenbuch der Hochfrequenztechnik by Meinke/Gundlach) can give an idea. You see that the total stub length is λ/2, with a bend in the middle. The bend point distance from the waveguide wall is λ/4, associated with a current "knot" of the standing wave. So leakage into the inter-flange gap (marked as "Kontakt") can be effectively cancelled.

 

is that pic for a microwave oven or a waveguide choke flange ?

I accept that there my be considerable differences between uWave oven doors and waveguides and their choke flanges


FvM, what is that kontakt dark line ? kontakt = contact ? contact with what ?

annotated that pic of mine above ( which is the same as all my 10GHz choke flanges)





Dave
 
Last edited:

The picture shows a waveguide flange. The dark line is part of the gap between both flanges. It's almost identical to the "choke joint" figure in the radartutorial.eu link, except for the direction of the first gap segment which doesn't matter in transmission line terms.

The potentially misleading point is that the figures don't refer to the obvious, the 1/2 wave transformer property of the complete design.

For the oven door design, I would prefer to see a scheme of the initially discussed geometry.
 

ohhh crap ... I have just seen the error of my ways

and just done a measurement putting a straight edge (as shown by the thick white line on the right pic) across the full flange
there is a 1mm gap between that inner section of the flange leading to the slot and the bottom of the straight edge
To be honest, I don't know if I have ever noticed that before and didn't recognise it from the drawings


well talk about being red faced
sorry for my arguments

Dave
 

Attachments

  • flange.JPG
    23.4 KB · Views: 274
Thanks, David and Jiripolivka,
It is the first time that I see the inner gap.
And I am curious about the 1mm gap, how long opened in the inner cavity? 1/4lamda?

- - - Updated - - -

Or just along the inner perimeter? all inner cavity is cut?
 

hi Tony

on the left section of my image where you are looking straight on to the end of the WG
Everything inside the ringed slot ( the bit with that blue 1/4 wave arrow on it) is lower than the rest of the flange that is outside the ring


Dave
 
Thanks, Dave.
Although I have seen various flanges from S band to Ka band, but in S band the slot filled with rubber seems not 1/4 lamda of S band. Am I right?
 

Status
Not open for further replies.

Similar threads

Menu
Log in
Register
Cookies are required to use this site. You must accept them to continue using the site. Learn more…