Microcontrollers and GSM projects(remote process control)

[parin_shah]

gsm projects

Dear friends,

I want information about the interfacing AVR micro controller atmega8535 with for sending and receiving the messages through microcontroller unit via mobile phones in order to decode the sms and do necessary process control in the device interfaced with the micro controller. If anybody have any information about the above topic then help me.

Thankx.....

Parin shah

 

[alzomor]

gsm module projects

Hi

Check the microcontroller section of edaboard
you will find much information

Salam
Hossam Alzomor
www.i-g.org

 

[xakker]

gsm module project

hi

blue tooth can also be used for this purpose. as far as i know microwaves and some door locks operate in same frequency band as of bluetooth.

 

[xakker]

gsm controlled projects

the document is not of much help..any one knows how to interface cellphone with PC or microcontroller

 

[mowgli]

gsm remote project

Hi,
on the market are available several GSM combiner modules. You can try to search in the web for the manufacturers of these devices and then try to see if there are some application notes or reference design which could be helpful for your project.

Mowgli

 

[carrier]

gsm microcontroller

go to elektor maganin in march 2002

 

[prinsloo]

bascom gsm

EPE Magazine has made an project available on cellphone interfacing.March April May 2007.Use a Nokia 5110 3310 3210 & 6110.
4 inputs 8 outputs.

Regards
Johan

 

[xakker]

gsm controller project

can anyone post a link to that project

 

[abicash]

gsm remote control projects

**broken link removed**
try above link.the fellow has done good work using the FBUS in nokia fones

 

[xakker]

project gsm module

where to find the cable to conect to a nokia phone thru fm bus

 

[Nandulal]

application of microcontroller in gsm

You need the GSM modem. I think that is controlled over serial bus. It can programmmed through AT commands.

 

[Vinay1277]

projects on gsm modules

I have done a project on this MCU is different but process and logic can be same . For this you need to have a gsm modem/mobile which support AT command . In terms of hardware it should have TTL/RS232 port for serial communication . You can learn AT commands by connecting two such modem to hyperterminal of computer . You can try to dial a no send SMS receive SMS in hyperterminal . Once you are confident in it try to do ,whatsoever you have done in hyperterminal ,same thing using serial port of your MCU using your own software and compiler . After this you can customise it for you application and list of probable application is very large . I used SIM300 gsm module with RS232 port Bascom compiler and P89C51RD2BN mcu. I hope you will find my line of action useful if yes please acknowledge .

Added after 2 minutes:

I have done a project on this MCU is different but process and logic can be same . For this you need to have a gsm modem/mobile which support AT command . In terms of hardware it should have TTL/RS232 port for serial communication . You can learn AT commands by connecting two such modem to hyperterminal of computer . You can try to dial a no send SMS receive SMS in hyperterminal . Once you are confident in it try to do ,whatsoever you have done in hyperterminal ,same thing using serial port of your MCU using your own software and compiler . After this you can customise it for you application and list of probable application is very large . I used SIM300 gsm module with RS232 port Bascom compiler and P89C51RD2BN mcu. I hope you will find my line of action useful if yes please acknowledge .

Added after 6 minutes:

I have done a project on this MCU is different but process and logic can be same . For this you need to have a gsm modem/mobile which support AT command . In terms of hardware it should have TTL/RS232 port for serial communication . You can learn AT commands by connecting two such modem to hyperterminal of computer . You can try to dial a no send SMS receive SMS in hyperterminal . Once you are confident in it try to do ,whatsoever you have done in hyperterminal ,same thing using serial port of your MCU using your own software and compiler . After this you can customise it for you application and list of probable application is very large . I used SIM300 gsm module with RS232 port Bascom compiler and P89C51RD2BN mcu. I hope you will find my line of action useful if yes please acknowledge .

 

[Van der Waals]

top projects of microcontrollers list

Hello everybody,


I would like to know how to connect my GSM module (SIM300) to my microcotroller (PIC 18F4525) ??. I have to command the GSM module so that it dial a number if an input of the PIC 18F4525 is activated, aslo the SIM300 should be able to activate a relay (in the outputs of the Microcontroller) by AT command ?


thanks in advance.