How to use a single antenna with two transceivers.

Status
Not open for further replies.
B

bugsbunnyboss

Junior Member level 3
Joined
Jul 10, 2012
Messages
29
Helped
0
Reputation
0
Reaction score
0
Trophy points
1,281
Visit site
Activity points
1,515
I have two transceivers. One main and another for backup. Now I am using two separate antennas for the two transceivers. Is there any device with which I can use both the transceivers with a single antenna? As mentioned already, all the parameters are same for both the transceivers and I have a switching mechanism to activate the secondary transceiver if the main one fails.

Any help would be appreciated.
 

Why you don't use a switch between antenna and transceivers?
Would be simplest way!
 
Dpending on the power level and frequency you can either use a semiconductor switch (e.g. GaAs) or coaxial relays.
 

Switch maybe a good solution. You have a photo/schematic of this devices ? The tranceivers are half/full duplex? I say this cause maybe you have problem with inteferences
 

use pin diode to make a switch,and you'd better receive the two signals by time division
 

FvM said:
Dpending on the power level and frequency you can either use a semiconductor switch (e.g. GaAs) or coaxial relays.
Click to expand...


Power level is 1 watt and frequency it is the ISM 434 MHz band.

- - - Updated - - -

Fovakis said:
Switch maybe a good solution. You have a photo/schematic of this devices ? The tranceivers are half/full duplex? I say this cause maybe you have problem with inteferences
Click to expand...

The transceivers are half duplex, and I wont be using both transceivers at the same time. The second transceiver has the same configuration as the first one and it is only for redundancy.
 

bugsbunnyboss said:
The transceivers are half duplex, and I wont be using both transceivers at the same time. The second transceiver has the same configuration as the first one and it is only for redundancy.
Click to expand...

Do you expect the second transceiver to take over automatically in the event the first fails, or can it be with manual human intervention?

If it can be done with human intervention, then personally my solution would be to unscrew the antenna feeder from one transceiver and screw it onto another. Total cost $0. If not a manual coaxial switch. At one Watt, assuming your transceiver would accept 1 mW without damage, then you only need an isolation of 30 dB, which is nothing really.

If you want the second transceiver to take over auotmatically if the first fails, then it is a whole different ball game.

Dave
 
Last edited:

The redundancy tranceiver is connected to your circuit or you have it for backup when the first fails? I mean, this will work at the same time with the main tranceiver? explain a little more about the use of redundancy tranceiver

George
 


I need it to take over automatically. The transceiver will automatically switch over. but my doubt is how do I use one antenna with both the transceivers? Will a coaxial switch do the job as biff44 suggested?

- - - Updated - - -

Fovakis said:
The redundancy tranceiver is connected to your circuit or you have it for backup when the first fails? I mean, this will work at the same time with the main tranceiver? explain a little more about the use of redundancy tranceiver

George
Click to expand...

The redundancy transceiver will automatically take over, if the primary fails. Both the transceivers are connected to a main control circuit which will do the switching automatically. I want to use one common antenna instead of using two antennas for the two transceivers (just to save space). If I am using a switch what should be the minimum isolation?
 

The switch I posted is a little overkill for 1 watt transmit power. You can use pretty much any electromechanical latching type RF relay switch at those power levels. The switch will not know when your transmitter has failed, so you will have to generate a signal separately to switch it into the standby transmitter position.

You could fairly easily find a semiconductor switch to do the same thing, but the electromechanical latching relay is probably a little more robust.
 

You'll find GaAs switches with up 10W power handling from major manufacturers, e.g. Hittite, RFMD or Skyworksinc. Reliability requirements may suggest a mechanical relay though.
 

What kind of failure events are we talking about here? If you're just worried about the transceiver dying due to downstream conditions, then a solid state switch should be fine. But if you're worried about lightning hitting the antenna, then you're looking at a much bigger issue...
 
Reactions: Ow@i$

    O

    Ow@i$

    Points: 2
    Helpful Answer Positive Rating
I have the same question. when and why a traneiver fails? i am a begginers so explain it simply if you can

George
 

Status
Not open for further replies.

Similar threads

Menu
Log in
Register
Cookies are required to use this site. You must accept them to continue using the site. Learn more…