How come the units of impedance of capacitor and coil are at Ohms ???

Status
Not open for further replies.

segevron

Newbie level 3
Joined
Apr 11, 2012
Messages
4
Helped
0
Reputation
0
Reaction score
0
Trophy points
1,281
Visit site
Activity points
1,310
My question is at the title -

Does anyone can explain me please how come the units of impedance of capacitor and coil are at Ohms ???

thanks ,

Ron.
 

The reactance of a capacitor and a coil are measured in ohms. You can call the reactance "the impedance".
A speaker has a coil. Its impedance at about 400Hz is usually 8 ohms but some are made at 4 ohms. My car had 2 ohm speakers.
 

Ohms is the standard unit defined for electrical resistance. Now, just because it is "ohms" doesn't mean that it cannot be a VECTOR (or some call it phasor) value instead of a SCALAR. The difference here is that the vector value has real, and imaginary axis components, whereas a scalar is simply a single value without these dimensions. An IDEAL capacitor would have its impedance purely on the imaginary axis with no "real" component. Likewise, an inductor/coil (but with opposite imaginary axis orientation). As real devices are not ideal, the do have some combination of both, with the vector addition of the two being the total impedance, in ohms, for the component.
 

Hi Ron and Audioguru,

"In electrical engineering, impedance is a measure of the extent to which a circuit opposes the flow of electricity. All materials have some degree of electrical resistance, which causes some energy to be lost as heat, and reduces the flow of current. In the case of direct current (DC), impedance is the same as resistance, and depends solely upon the materials from which the circuit is made. For an alternating current (AC), however, two additional factors can contribute to the impedance: capacitance and inductance. Together these are known as reactance, which is a measure of opposition to a change in current that depends on its frequency, and on the components of the circuit.

Alternating current is constantly changing direction, and does so at a given frequency, which is measured in Hertz (Hz), or cycles per second. Typically, electricity is supplied at 50 or 60 Hz, but this may be changed for specific applications. The frequency can be displayed as a wave on an oscilloscope in terms of current or voltage, with the distance from crest to crest representing a complete cycle. The degree of reactance in a circuit is dependent upon the frequency of the AC supply. More specifically, capacitive reactance decreases with increasing frequency, while inductive reactance increases.


Capacitive Reactance
A capacitor is a device that can store an electrical charge, and later release it. It generally consists of a non-conducting material, or insulator, sandwiched between two metal plates. As part of a circuit, it allows a charge to build up in the insulator and effectively stores energy in an electric field. As the charge increases, the current is reduced. After a certain time, the capacitor will be unable to absorb any more charge and the current will drop to zero, at which point it will discharge, producing a flow of electrons in the opposite direction.

If, however, the AC frequency is high, the current will change direction in less time than the capacitor takes to “fill up.” Since the current is at its maximum at the start of a cycle, a high frequency AC supply will be virtually unaffected by a capacitor. In contrast, if the frequency is low, this will allow time for some charge to build up in the capacitor, causing a reduction in current before the next cycle. Capacitors are used in many popular devices and gadgets, and so capacitive reactance is usually an important factor in impedance.


Inductive Reactance
Inductance is the tendency of a changing current flowing through a wire to induce an opposing current in a nearby conductor. This happens because a changing electrical current produces a changing magnetic field, which in turn causes electrons to flow in any conducting material within its range. When a wire is wound into a coil, it forms an inductor, and will induce an opposing flow of electrons, or electromotive force (EMF) in itself. The voltage of the induced EMF increases with the rate of change of the supply voltage, so increasing the AC frequency will increase the inductive reactance. Like capacitors, inductors are commonly used components.


Capacitors and Inductors in Combination
When both devices are present in a circuit, the effects depend not only on the AC frequency, but also on how they are wired. If a capacitor and inductor are connected in series, the current initially rises with frequency, reaching a maximum at a certain point, known as the resonance frequency, and falls thereafter. If they are wired in parallel, the current falls with rising frequency until a point is reached where none flows. Beyond this point, the flow rises again.
Measurement and Units

Like resistance, reactance and impedance are measured in ohms. In equations, impedance is normally represented by the symbol Z, and reactance by X. Capacitive and inductive reactance are represented by XC and XL, respectively. Similarly to Ohm’s law for resistance, overall impedance can be expressed as Z=V/I, where Z is given in ohms; V is voltage, given in volts; and I is current, given in amps."

http://www.wisegeek.org/what-is-impedance.htm



Best regards,
Peter
 

Status
Not open for further replies.
Cookies are required to use this site. You must accept them to continue using the site. Learn more…