Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Voltage gain of audio power amplifier

Status
Not open for further replies.
B

BenzT

Junior Member level 3
Junior Member level 3
Joined
Mar 24, 2017
Messages
27
Helped
0
Reputation
0
Reaction score
0
Trophy points
1
Visit site
Activity points
224
Hi
The voltage gain of Lm386 is given as 200 by connecting a capacitor.

What is the voltage gain mean here in audio power amplifier?
 

Hi,

V_out = gain x V_in

example:
10mV input (lets say RMS, 1kHz), Gain = 200
V_out = 200 x 10mV = 2000mV = 2V

(The datasheest shows always the same "Application curve". I´d call this an error. From the shape it could be the "bass boost curve")

Klaus
 
  • Like
Reactions: BenzT

    B

    BenzT

    Points: 2
    Helpful Answer Positive Rating
I ground the Inverting pin. Supply 8V. Gain 200. Frequency 40 Hz. Input given to Non Inverting pin.

My observation:
1. Input Peak to peak = 38mV. Output Peak to peak= 6.2V
2. Input Peak to peak = 22mV. Output Peak to peak= 3V

Why the full gain is not apply here....
 

Hi,

I ground the Inverting pin. Supply 8V. Gain 200. Frequency 40 Hz. Input given to Non Inverting pin.
Click to expand...
40Hz simply is no useful audio frequency for this low power amplifer.

Most probably you connected the 10uF at the GAIN pins.
Then you may expect a cutoff frequency of about 106Hz (here the 150 Ohms dominate)
fc = 1 / ( 2 x Pi x 150 Ohms x 10uF)
(Because of circuit this is no exact calculation)

Klaus
 
  • Like
Reactions: BenzT

    B

    BenzT

    Points: 2
    Helpful Answer Positive Rating
Also, read the datasheet, specifically "output voltage vs supply voltage". The maximum peak to peak voltage is (roughly) 1V - 2V less than the power supply rail, due to diode and transistor junctions at the output. It is not advertized as a rail-to-rail type of amplifier. 6.2V p-p output with a supply voltage of 8V is exactly in line with the product specification.
 
  • Like
Reactions: BenzT

    B

    BenzT

    Points: 2
    Helpful Answer Positive Rating
The maximum gain of LM86 is 200.

Is there any similar IC with the gain around 400?
 

Hi,

There are a lot of audio amplifiers where you are free to set (about) any gain.
The LM86 is somehow special with this.

You say similar.
You need to specify this. Similar in kind of: price, size, power, voltage, current, part count...
I recommend to go to a audio IC manufacturer´s web site and use their selection tool.

Klaus
 

Well similar to Price, Voltage. Power is not important for me. Low power is sufficient.

For a peak to peak input of 10mV, i want the output voltage of 3V(pk-pk).
 

3V/10mV= a gain of 300 times. The LM386 is cheap and is not really hifi since with a gain of 200 times its hiss can be heard and will be worse with a gain of 300 times.

Here is a 22 ohm resistor in series with a capacitor to ground to make a gain of 1000 times. Increase the value of the resistor for less gain:
 

Attachments

  • LM386 extra gain.PNG
    LM386 extra gain.PNG
    11.7 KB · Views: 209
  • Like
Reactions: BenzT

    B

    BenzT

    Points: 2
    Helpful Answer Positive Rating
Audioguru said:
Here is a 22 ohm resistor in series with a capacitor to ground to make a gain of 1000 times. Increase the value of the resistor for less gain:
Click to expand...

I tried this circuit for 1000 gain in Proteus simulation. For the 10mV(pk-pk) input, i am only getting 100mV(pk-pk) only.
Supply 8V. Gain 1000. Frequency 200 Hz.
 

Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top