Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

How to convert a Normally Open (NO) inductive proximity switch to Normally Closed

Status
Not open for further replies.
D

dineshdeshmuk

Full Member level 5
Full Member level 5
Joined
Sep 12, 2011
Messages
285
Helped
18
Reputation
36
Reaction score
18
Trophy points
1,298
Activity points
3,131
How to convert a Normally Open (NO) inductive proximity switch to Normally Closed (NC) one ?

Can we use a relay ? If yes, then, of how many pins & how to wire it up ?

Can we converter NPN inductive Proximity Switch to a PNP inductive Proximity Switch by the same fashion ?

thanks
 

I don't know about NPN inductive Proximity Switch. but NO can be converted to Normal close with a by using a relay in series with the proximity switch and using its normally closed contact
 
How to convert a Normally Open (NO) inductive proximity switch to Normally Closed (NC) one ?
Click to expand...

Example
ProxSw_Relay_01.jpg

ProxSwitch wiring ...................
ifm_wiring_01.jpg
ifm_wiring_02.jpg

Good selection of sensors, accessories, data and info..............
automation technology - ifm international
 
Last edited:
A normal open contact cant be physically converted to NC. if the switch has three terminals then one of them will be common, one will be normal open and one will be normal close.
 
kak111 said:
Example
View attachment 62744

ProxSwitch wiring ...................
View attachment 62746
View attachment 62747

Good selection of sensors, accessories, data and info..............
automation technology - ifm international
Click to expand...

Does the output of a NPN proximity switch (sensor) negative ? Negative w.r.t what ? what reference ?
Does the output of a PNP proximity switch (sensor) positive ? Positive w.r.t what ? what reference ?

Question regarding the wiring diagram that you provided :

Use NC contact of the relay in all of the four (4) different cases ????

Of what pin relay should be used ?

thanks
 

FvM said:
Look sharp. kak111's example circuit answers your questions completely.
Click to expand...

Does the output of a NPN proximity switch (sensor) negative ? Negative w.r.t what ? what reference ?
Does the output of a PNP proximity switch (sensor) positive ? Positive w.r.t what ? what reference ?

Question regarding the wiring diagram that you provided :

Use NC contact of the relay in all of the four (4) different cases ????

Of what pin relay should be used ?

thanks
 
Does the output of a NPN proximity switch (sensor) negative ? Negative w.r.t what ? what reference ?
Click to expand...
Yes, switches -supply voltage, reference +suply voltage.
Does the output of a PNP proximity switch (sensor) positive ? Positive w.r.t what ? what reference ?
Click to expand...
Yes, switches +supply voltage, reference -suply voltage.
Use NC contact of the relay in all of the four (4) different cases ????
Click to expand...
Yes
 
dineshdeshmuk said:
How to convert a Normally Open (NO) inductive proximity switch to Normally Closed (NC) one ?

Can we use a relay ? If yes, then, of how many pins & how to wire it up ?

Can we converter NPN inductive Proximity Switch to a PNP inductive Proximity Switch by the same fashion ?

thanks
Click to expand...

Have you a part number?
 
Here is simple answer, I use this for alarms, also isolate sensor from main circuit :

Senzor NC NO Connections.jpg

Also You can use 12V voltage if You put some higher resistor, and make sure to make good calc for resistor for diode in optocoupler (lower as possible for lower consuption of current).

Also with this You can make very chip laser alarm with one photo transistor and cheap laser torch.

Senzor NC NO Connections (3 variants).jpg
 
Last edited:
Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top