Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

SPI Working Code! two PIC - MikroC

Status
Not open for further replies.
R

RuH_iranga

Junior Member level 3
Junior Member level 3
Joined
Nov 4, 2010
Messages
31
Helped
7
Reputation
14
Reaction score
6
Trophy points
1,288
Location
sri lanka
Activity points
1,480
Hi all

This code is working on Proteus as well as tested on 18F452 (Master) and 16F877a (Slave).
Compiler- MikroC
I tried this one several times but it didn't work. When I changed the inbuilt "Spi_read()" command and used direct Registry reading as in the data sheet. Then it worked.

Master
Code: 
// Mikroc codes for SPI master device


void main()

{    INTCON.GIE = 1;
     //ADCON1=0b00000111;
     trisc=0b00010000;
     trisd=0b00000000;
     //trisa=0b00000000;
     portd.f1=1;
     
     SSPSTAT.SMP=0;
     SSPSTAT.CKE=0;
     SSPCON.SSPEN=1;
     SSPCON.CKP=1;
     SSPCON.SSPM3=0;
     SSPCON.SSPM2=0;
     SSPCON.SSPM1=0;
     SSPCON.SSPM0=0;
     
     //Spi_Init_Advanced(MASTER_OSC_DIV4, DATA_SAMPLE_END, CLK_Idle_HIGH, LOW_2_HIGH);

     while(1)
     {
       portd.f1=0;
       SSPCON.WCOL=0;
       Spi_Write(102);
       portd.f1=1;

       portd.f2=0;
       SSPCON.WCOL=0;
       Spi_Write(254);
       delay_ms(100);
       portd.f2=1;
       portd.f2=0;
       SSPCON.WCOL=0;
       Spi_Write(1);
       delay_ms(100);
       portd.f2=1;
     }
}

Slave
Code: 
// Mikroc codes for SPI slave divice
// SIMULATION SUCCEED DSN IN My Doc PLATFORM FOLDER

void main()
{
     unsigned int buffer, gdata =0;
     trisa=0b00100000;
     trisc=0b00011000;
     trisd=0b00000000;
     trisb=0b00000000;
     INTCON.GIE = 1;
     SSPSTAT.SMP=0;
     SSPSTAT.CKE=0;
     //SSPCON.SSPOV=0;
     SSPCON.SSPEN=1;
     SSPCON.CKP=1;
     SSPCON.SSPM3=0;
     SSPCON.SSPM2=1;
     SSPCON.SSPM1=0;
     SSPCON.SSPM0=0;
     //Spi_Init_Advanced(SLAVE_SS_ENABLE,DATA_SAMPLE_END,CLK_Idle_HIGH,LOW_2_HIGH);

     while(1)
             {

             if(SSPSTAT.BF)
             {
                gdata=SSPBUF;
                SSPCON.SSPOV=0;
             }



                     // gdata=Spi_Read(0);
                      if(gdata>100)
                      {
                      portb.f6=1;
                      portb.f7=0;
                      //delay_ms(20);
                      }
                      else
                      {
                      portb.f6=0;
                      portb.f7=1;
                      //delay_ms(20);
                      }

             }
}

Slave 2
Code: 
// Mikroc codes for SPI slave divice
// SIMULATION SUCCEED DSN IN My Doc PLATFORM FOLDER

void main()
{
     unsigned int buffer, gdata =0;
     trisa=0b00100000;
     trisc=0b00011000;
     trisd=0b00000000;
     trisb=0b00000000;
     INTCON.GIE = 1;
     SSPSTAT.SMP=0;
     SSPSTAT.CKE=0;
     //SSPCON.SSPOV=0;
     SSPCON.SSPEN=1;
     SSPCON.CKP=1;
     SSPCON.SSPM3=0;
     SSPCON.SSPM2=1;
     SSPCON.SSPM1=0;
     SSPCON.SSPM0=0;
     //Spi_Init_Advanced(SLAVE_SS_ENABLE,DATA_SAMPLE_END,CLK_Idle_HIGH,LOW_2_HIGH);

     while(1)
             {

             if(SSPSTAT.BF)
             {
                gdata=SSPBUF;
                SSPCON.SSPOV=0;
             }



                     // gdata=Spi_Read(0);
                      //if(gdata>103)
                      //{
                      portb=gdata;
                      //portb.f6=0;
                      //portb.f7=1;
                      //delay_ms(20);
                      //}
                      //else
                      //{
                     // portb.f6=1;
                     // portb.f7=0;
                      //delay_ms(20);
                     // }

             }
}
 

r_guna_sekar said:
please add the schematic...
Click to expand...

Hi, I did this before several months. Slave 2 is the bottom PIC (U3).
please ask for further clarifications.


Picture1.jpg

this will work!
 
thank you RuH_iranga , it's really helpful
 

Hi
Thank you for your post but I don't understand the part where u say " I changed the inbuilt "Spi_read()" command and used direct Registry reading as in the data sheet. Then it worked"

Can you clarify that more.

Regards.
 
In place of " Spi_read() " he used

if(SSPSTAT.BF)
{
gdata=SSPBUF;
SSPCON.SSPOV=0;
}
in slave side.
 

Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top