Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Looking for H bridge control circuit

Status
Not open for further replies.
A

attrib

Junior Member level 1
Junior Member level 1
Joined
Mar 8, 2002
Messages
17
Helped
0
Reputation
0
Reaction score
0
Trophy points
1,281
Location
México
Activity points
37
tip126 h-bridge

I need the control circuit..... so if u have and idea...... an interesting article that u want to share....... don't doubt to email me... I know that in the market exist several CI that can do the job..... but i would like to do it in a analog form.
for your time
thanks
Atte.
Attrib
 

H-Bridge

Its qiute simple -> you have only take care of the bias voltages of the used transistors.

so if you are using TIP121 and TIP126 as the complementary transistors, the bias voltage will be about 1.4V (because thei are darlingtons) -> so you will need an opamp which reaches this or you can use a digital device which drives the bridge.

i built a pwm temp-controller with this type of transistors
 

Re: H-Bridge

Do u have the diagram?? i am really interested about your desing :)
I hope that u can help me.
:)
Atte.
Attrib
 

A standard H-bridge uses 4 switches (transistors usally). Two high side and two low side. For easy of implementation, use P and N channel FETs. If you use just N channel, unless you use a biasing voltage, you will get shoot through and burn them up. Try looking at the L298N
 

h bridge

A classical way to drive an H-dridge is using a PWM signal & a SIGN signal.

if your bridge looks like this:

VCC
HL HR
|-M-|
LL LR
GND

with M : your load (a motor ?)
HL : P mosfet
HR : P mosfet
LL : N mosfet
LR : N mosfet


when SIGN=1 (HL = LR = OFF )

PWM - 0 - 1 - 0 - ...
HR & LL -OFF-ON-OFF-...

when SIGN=0 (HR = LL = OFF )

PWM - 0 - 1 - 0 - ...
HL & LR -OFF-ON-OFF-...

It's one solution before others. It depends on your needs.
rem : If your load is inductive : don't forget to add fast-recovery diodes for each transistor.

Good luck
 
  • Like
Reactions: K2d2

    K

    K2d2

    Points: 2
    Helpful Answer Positive Rating
They have h-bridge ic's avaiable.. search on google
 

h bridge

Thanks for your help.... i build it with your instructions and works very well..... and we can add some dead time....
Is only for security....
I used a non lineal load in this case the motor...... so again Thanks.....
Atte.
Attrib
 

Re: help with H bridge......

Yes you can bulid own H bridge.

But I suggest National LMD18200.
 

Re: h bridge

samsuffy said:
when SIGN=1 (HL = LR = OFF )

PWM - 0 - 1 - 0 - ...
HR & LL -OFF-ON-OFF-...

when SIGN=0 (HR = LL = OFF )

PWM - 0 - 1 - 0 - ...
HL & LR -OFF-ON-OFF-...

It's one solution before others. It depends on your needs.
rem : If your load is inductive : don't forget to add fast-recovery diodes for each transistor.

Good luck
Click to expand...

Hi samsuffy!

I want to control on my H-bridge circuit, with NPN and PNP transistors, as you have described but I have no idea how to implement it. please could you attach the connection diagram for the control circuit? I have tried many different options now and I can't seem to get it right.

Its good to know that there are people out there who know what others need to know. All one must do is ask.
K2d2
 

Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top