Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

dspic 30f2020 smps controller problem

Status
Not open for further replies.
alec82

alec82

Advanced Member level 4
Full Member level 1
Joined
Oct 25, 2006
Messages
118
Helped
12
Reputation
24
Reaction score
4
Trophy points
1,298
Visit site
Activity points
1,874
30f2020

hello guys
i'm working with dspic30f2020 for switch mode power supply .

the chip is too hot . in datasheet says it consume 200ma in normal mode
anybody have any experience with this?
 

dspic30f smps data sheet

Dear Alec,

Check wheather the I/O pins of the DSPic is geting loaded in any section of the Smps. The main reason may be any flaws in the design of bias circuit of the Power device .check it out.

Regards,
S.Vigneshwaran
 

dspic

dear vigneshwara_s
in attachment u can find the datasheet and dc charactristic of the mentioned device
regards


vigneshwara_s said:
Dear Alec,

Check wheather the I/O pins of the DSPic is geting loaded in any section of the Smps. The main reason may be any flaws in the design of bias circuit of the Power device .check it out.

Regards,
S.Vigneshwaran
Click to expand...
 

hot power supply for dspic30f

Dear Alec ,

For 250 ma the heat will be very normal. If it seems abnormal , Check the IO pins that you have connected to the power drivers.

How you had interfaced the IO line with the power driver ?.

Regards,
S.Vigneshwaran.
 

post in smps

vigneshwara_s said:
Dear Alec ,

For 250 ma the heat will be very normal. If it seems abnormal , Check the IO pins that you have connected to the power drivers.

How you had interfaced the IO line with the power driver ?.

Regards,
S.Vigneshwaran.
Click to expand...

dear vigneshwara_s
except of power supply ,all of IO not connected ( i don't connect next stage)
u haven't this problem with 30f2020?
regard
 

dspic smps

Dear Alec ,

If the Reset and Oscillator circuitry are Ok , then that would be the nominal heat o the Microcontroller.

So no need for you to worry .

regards,
AnSiSS.
 

smps dspic

ansiss said:
Dear Alec ,

If the Reset and Oscillator circuitry are Ok , then that would be the nominal heat o the Microcontroller.

So no need for you to worry .

regards,
AnSiSS.
Click to expand...

dear ansiss
the temprature rich up to 60°c in the room.
if ambient temprature rise and MCU work under hot condition it maybe damage
anyone have some experience with this?
regards
 

smps chip getting too hot

alec82 said:
ansiss said:
Dear Alec ,

If the Reset and Oscillator circuitry are Ok , then that would be the nominal heat o the Microcontroller.

So no need for you to worry .

regards,
AnSiSS.
Click to expand...

dear ansiss
the temprature rich up to 60°c in the room.
if ambient temprature rise and MCU work under hot condition it maybe damage
anyone have some experience with this?
regards
Click to expand...


I have the same phenomena.
At 5v supply voltage the chip (20MIPS) consumes about 180ma and it has about 40C rise above ambient.
This behavioral was observed at different chips on different boards. I guess it's normal.
 

dspic 30f2020

It is quite normal for these chips to be so hot. I have had this problem before using this chip as well as various other chips. They do run considerably cooler if you run at 3.3V instead of 5V. The other option is to buy a stick on heatsink.
 

    alec82

    alec82

    Points: 2
    Helpful Answer Positive Rating
Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top