Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

track and hold circuit for 8-bit folding adc

Status
Not open for further replies.
K

kickbeer

Full Member level 3
Full Member level 3
Joined
Nov 7, 2008
Messages
162
Helped
1
Reputation
2
Reaction score
0
Trophy points
1,296
Activity points
2,356
track and hold circuit

Hello,

Is there any recommedation whick track and hold i should use for my adc?

Input of that track and hold must be sinusoidal and has double ended output
 

folding adc

it depends to frequency.nevertheless i think you can use of simple switch with a capacitor (in the high speed ADCs). with fully differential topology, clock feedthrough will be removed. i think you can reach to the 48dB SNR, with this topology even in high frequency. as you know in high speed ADCs, you can't use of closed loop SH.
 

    K

    kickbeer

    Points: 2
    Helpful Answer Positive Rating
track and hold

speed of my a/d converter would be around 70 MHz. Can your show me some example? link etc...
 

adc close-loop sample hold

your speed is not high, i used of mentioned SH in my project(8bit,1GSPS). besides one of the important factors for choose topology of SH is a type of your ADC. unfortunately i didn't design folded ADC yet. for example if output of SH must drive large cap(parasitic cap), you won't able to use of simple SH and you have to use of SH that contains opamp. in closed loop SH(with opamp), current of opamp will charge parasitic cap whereas hold voltage on sampling capacitor, determines voltage of SH output.
 

    K

    kickbeer

    Points: 2
    Helpful Answer Positive Rating
track and hold adc

Monady said:
your speed is not high, i used of mentioned SH in my project(8bit,1GSPS). besides one of the important factors for choose topology of SH is a type of your ADC. unfortunately i didn't design folded ADC yet. for example if output of SH must drive large cap(parasitic cap), you won't able to use of simple SH and you have to use of SH that contains opamp. in closed loop SH(with opamp), current of opamp will charge parasitic cap whereas hold voltage on sampling capacitor, determines voltage of SH output.
Click to expand...


i don't dunderstand what u meant by this 'drive large capacitance'??
 

adc track&hold circuit

for example in flash ADC, 2^n comparator exists. these comparators have a large parasitic cap (it belongs to the parasitic cap of inputs of comparators), thus SH must drive large parasitic cap.
 

    K

    kickbeer

    Points: 2
    Helpful Answer Positive Rating
track & hold circuit

Monady said:
for example in flash ADC, 2^n comparator exists. these comparators have a large parasitic cap (it belongs to the parasitic cap of inputs of comparators), thus SH must drive large parasitic cap.
Click to expand...


the number of comparator in folding adc is much less than from flash. Mine has 40 comparators. does this considered to have large capacitances? is total input capacitances of 2pf large?

thx
 

ieindia.org

you should compare 2pF with value of sampling capacitor . i think it's better to test one open loop SH although it seems that you need to use of SH with opamp.besides search for some thesis or paper about folded, surely you'll find some beneficial info about this issue.
Good luck
 

    K

    kickbeer

    Points: 2
    Helpful Answer Positive Rating
track and hold circuit example

Hello!
At 70 MHz you should respect a lot of design rules and you should be almost professional to achieve guaranteed results.
But if you have a 100 times lower frequency it will be much easier.
Everything depends on your experience and resources.
May you will find something useful below:
Sample and hold basics:
**broken link removed**
**broken link removed**
http://analog.postech.ac.kr/3.Class/1.Classes/07_695O/SH.pdf
**broken link removed**
**broken link removed**
**broken link removed**
**broken link removed**
ADCs:
**broken link removed**
**broken link removed**
Sampling and conversion:
**broken link removed**
**broken link removed**
http://www.ieindia.org/pdf/88/88ET104.pdf
http://www.ieindia.org/pdf/89/89CP109.pdf
Hope that will help you a bit.
BR
 

Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top