Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

power electronics converter simulation in proteus

Status
Not open for further replies.
Fragrance

Fragrance

Advanced Member level 4
Advanced Member level 4
Joined
Jul 26, 2002
Messages
1,190
Helped
248
Reputation
496
Reaction score
202
Trophy points
1,343
Location
East Of Earth
Activity points
8,933
proteus models

hi here is new models

3 digit cc and ca dispaly multiplexed

3 didgit voltmeter chip TC7107(ICL7107)

Thumb switch with commom pin bcd and hex

regards
Fragrance
 

icl7107, proteus

thank you fragrance a lot>>>

i was searching for it

thank you

you are the best
 
new proteus

Fragrance said:
hi here is new models

3 digit cc and ca dispaly multiplexed

3 didgit voltmeter chip TC7107(ICL7107)

Thumb switch with commom pin bcd and hex

regards
Fragrance
Click to expand...

hey do you have proteus model for DS12887 RTC?
 

    V

    Points: 2
    Helpful Answer Positive Rating
Re: New Proteus Models

Hey i'm using proteus 7.4 sp3. I couldnt find DS1231 and LPC2388 in library. Can you please upload them...
 

i`m using proteus 7.7 and the tc7107 don't work; this say:

PIN 'GND' not modelled
PIN 'OSC1' not modelled
PIN 'OSC2' not modelled
PIN 'OSC3' not modelled
 

younlink said:
i`m using proteus 7.7 and the tc7107 don't work; this say:

PIN 'GND' not modelled
PIN 'OSC1' not modelled
PIN 'OSC2' not modelled
PIN 'OSC3' not modelled
Click to expand...


hi

these pin are not modeled any way or me it is working fine here is test jig for it

23_1287030703_thumb.jpg
 

Attachments

  • TC7107.rar
    8.8 KB · Views: 656
  • Like
Reactions: felixalilopez

    F

    felixalilopez

    Points: 2
    Helpful Answer Positive Rating
    V

    Points: 2
    Helpful Answer Positive Rating
I also need this kindly any one give me this file TC7101 of 7.1 sp2 proteus or any link of proteus 7.7 plz urgent..thanks
 

asmarhussain said:
I also need this kindly any one give me this file TC7101 of 7.1 sp2 proteus or any link of proteus 7.7 plz urgent..thanks
Click to expand...

converted to isis 7 format
 

Attachments

  • TC7107.rar
    15.2 KB · Views: 327
  • Like
Reactions: platinum12

    P

    platinum12

    Points: 2
    Helpful Answer Positive Rating
    V

    Points: 2
    Helpful Answer Positive Rating
dear Frinds .... i tried many times to apply the same circuit in the icl 7107 datasheet for range 200mV but it didnot work ,,,, i don't know why,,,,
here you r my file ,,, please download it and find where is my fult ,,,, the datasheet circuit is Here.... many thanks
 

MOhamad_Yhaya said:
dear Frinds .... i tried many times to apply the same circuit in the icl 7107 datasheet for range 200mV but it didnot work ,,,, i don't know why,,,,
here you r my file ,,, please download it and find where is my fult ,,,, the datasheet circuit is Here.... many thanks
Click to expand...

dear friend,

you did just two mistake in your design corrected design file uploaded here and also share your working circuit image what you did wrong never adjusted the ref voltage also never short the -vin and Acom you never required batteries to give power to circuit as it is virtual simulator so you just required power net hope this will clear every point further you can check this schematic.Digital voltmeter using ICL7107 - Electronic Circuits and Diagram-Electronics Projects and Design

59_1311662173.jpg

regards
Fragrance
 

Attachments

  • 7107 Datasheet Circuit.rar
    78.4 KB · Views: 348
  • Like
Reactions: xenoneng

    X

    xenoneng

    Points: 2
    Helpful Answer Positive Rating
    V

    Points: 2
    Helpful Answer Positive Rating
hi i gotta a question how can i connect ICL 7107 to an lcd not seven segment i mean i wanna use a lcd accept using 3 seven segment but the lcd is 16x2 and it has 7 internal ports but icl 7107 has 21 internal ports :(
 

galaxyboy said:
hi i gotta a question how can i connect ICL 7107 to an lcd not seven segment i mean i wanna use a lcd accept using 3 seven segment but the lcd is 16x2 and it has 7 internal ports but icl 7107 has 21 internal ports :(
Click to expand...

there is another version of the chip called ICL7106 which drive seven segment LCD display not 16x2 dot matrix LCD module

regards
Fragrance
 
hello guys,
7 segments showing strange numbers,
any idea whats wrong? using proteus 7.6

best regards circuit

Screenshot (2).png
 

Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top