Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

How to convert 230V A.C to 5V D.C with out using transformer

Status
Not open for further replies.

saumya_85

Advanced Member level 4
Full Member level 1
Joined
Mar 18, 2009
Messages
107
Helped
6
Reputation
12
Reaction score
5
Trophy points
1,298
Location
INDIA
Activity points
1,948
230v to 5v

How to convert 230V / 440V A.C to 5V D.C with out using transformer.

Is it possible?

Could any body help me out?
 

5v transformer

It is 100% possible to get 5 volts without transformers by the use of capacitors and resistors, but limited to some milliampheres. Also you may use a switch mode power supply. BTW what current you require?
 
230vac to 5vdc circuit

it depends on what's the current rating ...

read this to understand

**broken link removed**
 

    saumya_85

    Points: 2
    Helpful Answer Positive Rating
5v without transformer

Here below I've linked to a paper about this stuff, take care, capacitor power supply is different than conventional bridge-capacitor power supply, the first are basically constant current fed device, latter are voltage source. Anyway read the paper to gain more knowledge about performance, advantage, drawback and so on about this supply device class.

A Capacitor-Fed, Voltage-Step-Down, Single-Phase, Non-Isolated Rectifier **broken link removed**
 

    saumya_85

    Points: 2
    Helpful Answer Positive Rating
230v 5v

There's 2 ways you could do it:
1. CAPACITIVE TRANSFORMERLESS POWER SUPPLY or
2. RESISTIVE TRANSFORMERLESS POWER SUPPLY

Go to Microchip's web-site and do a search for application note: AN954

Good luck,

MFD
 
ac volte 230v to 5v convert do not transformer

Suppose i am using transformer. ok

I have planned for like below:

Direct supply to transformer Which will convert 230 V Ac to 24 v Then use of Bridge rectifier circuit then regulator supply circuit.

But When i am going different searches:

I found that they are using One Varistor & a Capacitor Across the AC Supply before the transformer.

Could anybody explain me What is the need/role of Varistor & capacitor before the transformer?

Why we need a varistor?

 

5v power supply without transformer

saumya_85 said:
Suppose i am using transformer. ok

I have planned for like below:

Direct supply to transformer Which will convert 230 V Ac to 24 v Then use of Bridge rectifier circuit then regulator supply circuit.

But When i am going different searches:

I found that they are using One Varistor & a Capacitor Across the AC Supply before the transformer.

Could anybody explain me What is the need/role of Varistor & capacitor before the transformer?

Why we need a varistor?




buddy u are asking same question every where ...do some googling too :D
 

    saumya_85

    Points: 2
    Helpful Answer Positive Rating
    V

    Points: 2
    Helpful Answer Positive Rating
230v ac to 5v dc

i already replied u in ,

#1139749
 

    saumya_85

    Points: 2
    Helpful Answer Positive Rating
what do represent by 230v ac

Hai Saumya-85. As you intend to get only 5 volts regulated DC, it is sufficient if you use a 9 volt transformer for the rectifier as the margin voltage required for regulation is about 3 volts above the required voltage. Capacitors are used to filter any ripples as well varistor is used to supress any spikes on the supply. Good luck
 

    saumya_85

    Points: 2
    Helpful Answer Positive Rating
circuit for costant 5v without using smps

Hi saumya

The main function of varistor is

to protect circuits against excessive transient voltages by incorporating them into the circuit in such a way that, when triggered, they will shunt the current created by the high voltage away from the sensitive components.

i think that main function of capacitor is supress noise and smoothen the input sinewave
 
230v to 5v circuit

Saumya, you did not answer the Pranam's query, what is the current demand from the 5V dc supplyu you want to make

if what all you need is say 5V 500mA, a transformer of 230 primary and 8V secondary with 750 mA capacity will do
You may use a 4 diode bridge rectifier, have a filter with 2000uF/16V. use a 7805 regulator IC and a good heat sink
with a 0.1 uF cap each connected at INPUT & OUTPUT TO common Gnd, AND WITH SAY 470uF/16V FILTER CAPACITOR at the output, you are ready to use it.
Ofcourse you need a container to house all these stuff.
Hope you can make a schematic from the explanation given.
download datasheet of 7805 from www.alldatasheet.com and study it
you will appreciate all issues .




.
 

    saumya_85

    Points: 2
    Helpful Answer Positive Rating
5 volt transformer

I require 5Volt DC with2A>I <3 Amp Current rating.

Current should be between than 2A to 3A.

But preferable 3A.
 
230v to 5v dc schematic

saumya_85 said:
I require 5Volt DC with2A>I <3 Amp Current rating.

Current should be between than 2A to 3A.

But preferable 3A.
You may consider making a switch Mode power supply. Link for datasheet of such design is attached. as collected from Power integration inc

http://www.powerint.com/sites/default/files/product-docs/tny274-280.pdf

they have Top, TINY and Link switches.
complete design can be obtained from their site. These chips are sold in India, so you should have no problems at all.
 

    saumya_85

    Points: 2
    Helpful Answer Positive Rating
230 5v ac dc schematic

saumya_85 said:
I require 5Volt DC with2A>I <3 Amp Current rating.

Current should be between than 2A to 3A.

But preferable 3A.
Hai Saumya_85, In case you need 5 volts at more ampheres, use 0-9 transformor 3A, rectify and filter the output and feed it to the High current voltage regulator which will supply 5 volts at 3amps..Do not forget the 'Helped me"button if you find this post has helped you. Good luck
 

    saumya_85

    Points: 2
    Helpful Answer Positive Rating
230 to 24 converter

pranam77 said:
saumya_85 said:
I require 5Volt DC with2A>I <3 Amp Current rating.

Current should be between than 2A to 3A.

But preferable 3A.
Hai Saumya_85, In case you need 5 volts at more ampheres, use 0-9 transformor 3A, rectify and filter the output and feed it to the High current voltage regulator which will supply 5 volts at 3amps..Do not forget the 'Helped me"button if you find this post has helped you. Good luck
Thanks pranam for your support.

Could u tell me why 2N2955 is required in your schematic?
 

trafo van 230 naar 5v

It is used too provide the 3 amps current, with the volatge at the regulated level. 5volts in this case. Do not forget to press the 'Helped me"button if you find this post has helped you. Good luck
 
230v bridge rectifier

pranam77 said:
It is used too provide the 3 amps current, with the volatge at the regulated level. 5volts in this case. Do not forget to press the 'Helped me"button if you find this post has helped you. Good luck




Thanks
 

230 ac to dc 5vdc

Hai Saumya.
Please note that these circuits given by me will work fine when you use it with the rectified and filtered DC derived from a transformer only.
 

    saumya_85

    Points: 2
    Helpful Answer Positive Rating
230 to 5v circuit

smxx said:
hi
It is may be danger to use 230-5v

YES it IS HAZARDOUS to use non isolated supplies, as many a times , our designed circuits are used by others without proper understanding and are sure to be ELECTROCUTED IF THEY COME INTO CONTACT unknowingly, and the responsibility directly falls on us if traced legally.
 

Status
Not open for further replies.

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top