Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

How to write a single pulse code (verilog) ?

Status
Not open for further replies.
D

dd2001

Full Member level 4
Full Member level 4
Joined
Apr 14, 2002
Messages
236
Helped
1
Reputation
2
Reaction score
1
Trophy points
1,298
Activity points
1,912
verilog one shot

Hi,

I don't know how to write verilog code to generate a single pulse?

Anyone can help?
 

verilog pulse

this code i had writen to act as a digital mono stable but it it VHDL coding, I hope it may help
 

one shot verilog

I'm not sure what your asking.. but theres this..

thing is a high going transition which creates a oneshot pulsy at the same time..


reg thing_dly;

wire pulsy;
assign pulsy = thing & ~thing_dly;

always @(posedge clk or posedge rst)
if(rst)
thing_dly <= 1'b0;
else
thing_dly <= thing;


If your looking for a quick pulse (say to clear a reg/combinatorial) then your coding the problem incorrectly.. never use gate delays.. there is always ways around it.. just hard to figure out..

jelydonut
 

verilog create pulse

I think this is what you want....
// Verilog code
module test001(clk, pulse, clkout);

input clk;
input pulse;
output clkout;

reg cnt, temp;
initial begin cnt = 0;
temp = 0;
end

always @(posedge clk)
if(pulse && !cnt) begin
cnt <= ~cnt;
temp <= 1;
end
else if(!pulse) begin
cnt <= 0;
end
else
temp <= 0;


assign clkout = temp|clk;

endmodule
 
  • Like
Reactions: tinkky

    T

    tinkky

    Points: 2
    Helpful Answer Positive Rating
verilog pulse

I think that generating a signal pulse must require a trigger signal.

best reagrds




dd2001 said:
Hi,

I don't know how to write verilog code to generate a single pulse?

Anyone can help?
Click to expand...
 

verilog generate pulse

I think it's no way to create a pulse in degital ckt,
(use a faster clock is not a pulse)
I think you need a hard-macro
(Delay cell, use spice to calculate the delay to meet your pulse width)
then in verilog:
wire pulse,pulsed,pulse_want;
dly(.out(pulsed), .in(pulse));
assign pulse_want = pulse& ~pulsed;
 
create a pulse in verilog

Ust two filp-flop to implement it.
 
one pulse code in verilog

Your problem is not very clear. If you are having a clock signal and an enable signal which when arrives you must give out exactly one pulse, then, you can use two flips flops clocked by the same clock.
O/p of the first flip flop goes as input to the second and the output of the second goes as I/p clear to the first, take o/p from the o/p of the first flip flop, this will be a single cycle pulse.
Your enable can be any cycle width. Nest pulse will be generated only when enable comes for the second time. Tell me if it is clear ???
 

verilog one-shot

from following attached file, you can find many design practice include

signle pulse generate.



best regards




dd2001 said:
Hi,

I don't know how to write verilog code to generate a single pulse?

Anyone can help?
Click to expand...
 

    V

    Points: 2
    Helpful Answer Positive Rating
pulse in verilog

Thanks!!!! It works fine.


jelydonut said:
I'm not sure what your asking.. but theres this..

thing is a high going transition which creates a oneshot pulsy at the same time..


reg thing_dly;

wire pulsy;
assign pulsy = thing & ~thing_dly;

always @(posedge clk or posedge rst)
if(rst)
thing_dly <= 1'b0;
else
thing_dly <= thing;


If your looking for a quick pulse (say to clear a reg/combinatorial) then your coding the problem incorrectly.. never use gate delays.. there is always ways around it.. just hard to figure out..

jelydonut
Click to expand...
:D:D
 
Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top