Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

[HFSS Question] how to setup CPW-fed ports?

Status
Not open for further replies.
B

blue_electron

Banned
Junior Member level 1
Joined
Jan 26, 2007
Messages
15
Helped
0
Reputation
0
Reaction score
0
Trophy points
1,281
Activity points
0
hfss cpw

hi,

im desgining a PIFA printed on FR4 with a CPW-fed port..
how to setup the ground plane at both ends of the middle feed-line?

thanks!
 

hfss cpw port

give me the model and i can set it for you
 

hfss port for cpw

I have a problem with the CPW feedline too (test)
 

hfss cpw ports

Search in the Electromagnetic Simulation board in this forum for this info. There's plenty of articles about this in that board.

Ananth.
 
hfss cpgw

I got a question,
should i ues the lumped port of wave port
since the two results are different
 

cpw port hfss

hi,
I have a similar probem.
I want to simulte CPW ,and I expect the structure of CPW give the standard impedance 50 Ohm.Because the substrate is thick silicon, lumped port seem
to be the better choice.
But the lumped port will not give the impedance result, and I have to provide impedance for the S-parameter results.
How can I solve this problem? Can anyone give me some suggestion?

Thanx!
 

hfss cpw lumped port

I give you an advice here, after finished your simulation, you must select port to plot vector-E, to make sure the E field is right. if it is not right, you can change the dimension of port. hope this helpful!

Edmund
 

waveport cpw hfss

CPW transmission lines often cause significant grief as they are "mode rich". I generally use wave ports in my analysis. Read the section on Impedance calculation in HFSS help. You will probably want to use the Zpi form and an impedance line. Make sure the mode and impedance line make sense by examining the port field configuration for each mode. You don't say if you are using single ended or differential CPW lines or if you have a lower ground plane. If the lines are differential, are they tightly (close) or loosely(wide spacing) coupled? Depending on these details the situation will change.

When all is done, I like to compare the results to Polar Instrument's calculator (or similar tool) to confirm that the results are reasonable. I specifically do not mean to imply that I think Polar is a better tool. I use it as a sanity check to help detect a blunder.
 
hfss coplanar waveguide.hfss

hi,
i have a question. if we use wave port mode for cpw feed line, how many modes do we need to describe? one or two? if we use one mode , the field in that side of antenna feed line described will b more strong than other.
 
hfss waveport for cpw

I have a similar problem. I m simulating a cpw fed patch antenna. I m using a waveport. But the fields at the waveport dont correspond to CPW mode. I have tried varying the size of the waveport....but with no improvement.
Has anyone successfully simulated CPW fed antennas in HFSS. Does HFSS handle CPW properly? Could someone tell me the correct steps in setting the CPW feed.
 

hfss cpw feed

thanks
it will help me a lot
 

wave port cpw hfss

thx very much.....
i have a similar questions in a long time.
 

assigning port of coplanar waveguide hfss

thanks
it will help me a lot

i really want this

Added after 2 minutes:

I design MMIC in CPW structure

but dont know how to simulate SPW in HFSS

thx a lot
 

cpw 50ohm hfss

thanks, it is really helpful~~~~~
 

cpw in hfss

the same problem for me ,thanks for answering!
 

cpw feed in hfss

I am also struggling with the problem . pse find the complete tutorial attached
 
  • Like
Reactions: bfv123

    B

    bfv123

    Points: 2
    Helpful Answer Positive Rating
Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top