Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

ICD-U40 - circuit and PCB

Status
Not open for further replies.

folks

Full Member level 3
Full Member level 3
Joined
Oct 30, 2006
Messages
179
Helped
32
Reputation
64
Reaction score
14
Trophy points
1,298
Location
Guadalajara
Activity points
2,337
icd-u40

ICD-U40 is a perfect solution for debugging and programming PIC. It's fully independant from MPLAB, well integrated in PCW and is quite cheap. It has very advantages vs ICD2, at least it's faster. Here is the circuit and PCB for those who want to make it themself.
**broken link removed**
The following times represent the time it takes to execute a single step command on a 1 Ghz PC:
MPLAB USB ICD-2 1.36 seconds
PCW serial ICD-S40 (40Mhz) 0.16 seconds
PCW USB ICD-U40 0.24 seconds

Don't ask me for the firmware, is very easy to obtain, this is in your PC :D

Regards......
 

icd-u40 schematic

folks said:
ICD-U40 is a perfect solution for debugging and programming PIC. It's fully independant from MPLAB, well integrated in PCW and is quite cheap. It has very advantages vs ICD2, at least it's faster. Here is the circuit and PCB for those who want to make it themself.

Being MPLAB independent is not necessarily a good thing. It supports its own IDE and appears to be reliant on CCS C which has a rather crippled demo version (2K program, limited PIC support PIC16F877, PIC16C544 and 16 bit PIC18F458)

Note: the 1.36Sec MPLAB USB ICD2 step rate seems more like RS232. Are you using a non 18F4550 version, that thing steps very fast.

PS on a side note; by the sheer number of programmer and or debugger threads here I often wonder if anyone actually builds projects or just spend all their time building programmers...

And an ugly interface IMHO.
**broken link removed**
 

icd-u40 schematics

Here is the PCB, SCHEMATIC and HEX file:
4qqcnz4.jpg


4qs6hac.jpg


52kt9gn.jpg


Remember Download And Thank Me....
 
icd u40 schematic

folks
very nice projects. How about debug on PCWH IDE ?
 

    folks

    Points: 2
    Helpful Answer Positive Rating
icd u40 clone

nooknikz said:
folks
very nice projects. How about debug on PCWH IDE ?

Hi nooknikz

Work perfect and very fast, I debug the pic18f4550 Step by Step in a powerful C debugger!!
 
icd-u40 firmware

Hi Folks,

Nice job !
Can I use a max232 instead FT232 ?
If possible , DTR signal must be inverted ?

Thanks
 

icdu40

wjr1955 said:
Hi Folks,

Nice job !
Can I use a max232 instead FT232 ?
If possible , DTR signal must be inverted ?

Thanks

Hi wjr1955

Yes you can use max232 and this programmer is called ICD-S40, keep the dtr signal non inverted and the ICD-S40 is powered from the target board
 

icd-s40

You need to swap anode and cathode of LED LD4
 
  • Like
Reactions: AbdulMoeez

    folks

    Points: 2
    Helpful Answer Positive Rating

    AbdulMoeez

    Points: 2
    Helpful Answer Positive Rating
icd-u40

is it possible to use 18f452 instead of 18f252 ?
if possible which firmware should be use?
 
icd-s40 clone

hi everyone,

i was in hurry when i post the board, and i miss something to mention:
- on this board you have just to make a wire connection between R40 and D3 -anod, on the bottom board.
This is because i forget to cut the Q1 colector and VPP led from the Vdd, with the D3 diode. And i also connect the Vpp led to the Vdd, instead the ground.
So i introduce the D3 diode after the pcb was finalized, and i put a via close to the R40, for this wire connection.

Added after 1 minutes:

dsMasoud said:
is it possible to use 18f452 instead of 18f252 ?
if possible which firmware should be use?
18f452 is a 40 pin device, not a 20 pin device as 18f252. But if you arrange the PCB and the firmware should work without any problems with the correct fuse settings. Like disabling the extra peripherals of 18f452 with the fuses.

Regards...
 

ccs icd-u40 schematic

Hi, folks.
Do you ave schematic for new revisions of ICD-U40, wich support dspic, or J series?

Thanks.
 

ccs u40 schematic

Hi. Any body have eeprom content for FT232R?

Thanks.
 

ıcd-u40 schematic

Here is the CCS U-40 or/and S-40 (either of them will do) debugger firmware. If you need...

**broken link removed**


Here is the original CCS ICD S40 schematic.


**broken link removed**
 

icd u40 circuit

Hi folks

are you have eeprom for FT232RL ? And how to program to FT232RL ?

Thank you very much
 

schematic icd-u40

NICE WORK FOLKS.

CAN WE USE 18F2550 INSTEAD OF 18F452 AND REMOVE FT232 ?
 

rapidshare.com/files easy-pc pcb

Hi. FT232R can be programmed with MProg but eeprom content is missing:
\\**broken link removed**

Best Regards.
 

icdu-40

nooknikz said:
Hi folks

are you have eeprom for FT232RL ? And how to program to FT232RL ?

Thank you very much

hi nooknikz
you have to download the datasheet for the rl chip, from the www.ftdichip.com and also the program utility for eeprom programmer, called MProg. (it was version 2.9c when i played with this). All avaible on the web page. Its quite easy to play with this utility.
this is the newest Ft232 chip, with eeprom inside the device, with no external crystal.
 

Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top