Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

help me, about ldv installation?

Status
Not open for further replies.

quan228228

Full Member level 4
Full Member level 4
Joined
Mar 23, 2006
Messages
196
Helped
16
Reputation
32
Reaction score
3
Trophy points
1,298
Activity points
2,571
When i install ldv50 under linux, do i must install software from cdrom?

Thanks!
 

No necessary. If you have the tar files, you can simply untar them. And then in the CD1 directory, you will find a script named setup.sh. Just run it with "./setup.sh".
 

tsinghua said:
No necessary. If you have the tar files, you can simply untar them. And then in the CD1 directory, you will find a script named setup.sh. Just run it with "./setup.sh".

yes. i have untar the files, and find setup.sh in CD1 directory. But i still can't install ldv50. The following are the installation process. Pls read it and teach me, Thanks !


Steps:
A: Main Menu
1) load available products
2) list installed products
3).......

Type your choice: 1 (I select 1st option)

B: CD#1 of the media ste being used is required
You must now identify where the cd_rom is mounted
1) local (mounted to this machine)
2) Remote (mounted to another machine)

Type your choice: 1 ( I select 1st option)


C: Specify the cd_rom mount point
1) cd_rom
2) other

Type your choice: 2 (I select 2nd option)

and then enter the dirctory of mount point: /tools/ldv50/cd1

The return infor is " image not found
unable to read media /tools/ldv50/cd1".


So, here, i cant continute install my software. My installation file is in dirctory "/tools/ldv50/cd1 and /tools/ldv50/cd2".

tsinghua,
Could you give me some advice? Thank you!

David


Any another guy's suggestions are welcome. Thank you all!
 

Hi!
I offer next =>
1. Create directory (Ex. /home/tmp_soft)
2. Untar all CD in this directory
3. Create directory where You will been LDV installs (Ex. /home/LDV5.0)
4. Go in directory where untar CD (Ex. /home/tmp_soft/CDROM1)
5. Start ./SETUP.SH in /home/tmp_soft/CDROM1

Try ...

Best regards!
 

    quan228228

    Points: 2
    Helpful Answer Positive Rating
Shurik said:
Hi!
I offer next =>
1. Create directory (Ex. /home/tmp_soft)
2. Untar all CD in this directory
3. Create directory where You will been LDV installs (Ex. /home/LDV5.0)
4. Go in directory where untar CD (Ex. /home/tmp_soft/CDROM1)
5. Start ./SETUP.SH in /home/tmp_soft/CDROM1

Try ...

Best regards!

Yes, i installed ldv50 like you said, but in 3rd step, ask me to Specify the cd_rom mount point , how should i do next?

Thanks for your advice!
 

Hi
Necessary be where exist SETUP.SH !!!!
installer will offer self the mount point
Is it not offer?
 

    quan228228

    Points: 2
    Helpful Answer Positive Rating
Shurik said:
Hi
Necessary be where exist SETUP.SH !!!!
installer will offer self the mount point
Is it not offer?

Installer offers the mount point. But i want to install the software from hardware instead of CD_ROM. Can i do like this ?

Very very thank you!
 

Hi.
Yes you are !!
You may look this documentation.

Best regards !
 

    quan228228

    Points: 2
    Helpful Answer Positive Rating
Shurik said:
Hi.
Yes you are !!
You may look this documentation.

Best regards !

I am very thankful to you. But in third step, i type the choice: 2 (other instead of cd_rom) and then enter the dirctory of mount point, but i can't find the similar directory like pdf file shows(/tmp/IC5141/.....).

How could i know my computer's cd_rom mount point?



THANK YOU VERY MUCH!

David
 

Hi quan228228 !!
In PDF file have the example show !

I can advise =>
1. You will copy your CDs on HD
CD1 into directory CDROM1
CD2 into directory CDROM2
2. Go into CDROM1
3. Installation start !

Try !!!

Added after 3 minutes:

Write the command
ls -laR /tools/ldv50/* > ls.txt

And send this file pls!
 

    quan228228

    Points: 2
    Helpful Answer Positive Rating
Shurik said:
Hi quan228228 !!
In PDF file have the example show !

I can advise =>
1. You will copy your CDs on HD
CD1 into directory CDROM1
CD2 into directory CDROM2
2. Go into CDROM1
3. Installation start !

Try !!!

Added after 3 minutes:

Write the command
ls -laR /tools/ldv50/* > ls.txt

And send this file pls!

I still cant. :cry:
Thank you taking so much time help me.

The attached file "ls.txt" shows files in installation directory "/tools/ldv50".
The attached file "cdrom1.txt" shows files of CD1 of software , "cdrom2.txt" shows files of CD2 of software.

David
 

I have seen your listing !! And I think the best there is change small letter
to uppercase letter !!
Ex.
fs.0 -> FS.0

TRY !!

When you will be install LDV, clear the directory where it will be installed.

Best regards !

Added after 4 minutes:

P.S.
Linux sensing by register of letters
 

    quan228228

    Points: 2
    Helpful Answer Positive Rating
Shurik said:
P.S.
Linux sensing by register of letters

yeah, :D:D:D you are right. I completed installation.
Thank you very very much. You are so nice, enthusiastic, good guy.

"Linux sensing by register of letters" is quitely right. At the beginning, i always change the uppercase letter to lowercase in setup.sh file, because there are less change to do than modifiying fs.* to FS.*.
Ok, i understand, linux is sensing by register of letters. This is the cause why i cant install the IC50 early.

:D Thank you very much. you are something.

David
 

I always make files into iso files, then mount them in /mnt
 

Status
Not open for further replies.

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top