Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

virtual serial port between Proteus and Hyper Terminal

Status
Not open for further replies.
R

ranaknight

Newbie level 6
Newbie level 6
Joined
Jul 7, 2006
Messages
12
Helped
1
Reputation
2
Reaction score
1
Trophy points
1,283
Activity points
1,354
hyperterminal serial port

Hi,

I am wanting to establish a virtual serial port connection between an 89c51 being emulated in Proteus and Hyper Terminal running in Windows.

How do I go about doing this ?

Thanks in advance
 
  • Like
Reactions: faruq

    F

    faruq

    Points: 2
    Helpful Answer Positive Rating
proteus serial port

I found a tool VIRTUAL TERMINAL in proteus.you can use this tool.
 
proteus hyperterminal

if you use two machines you need
a null serial cable {sometimes called a modem cable}

then connect two ports

to use hyperterminal you can also connect com 1 physical port to com2 physical port

set hypertermal to use only com 2
and the compim in isis only to use com1
1----2
tx->rx
rx<-tx
rst->cts
cts<rts
wire dtr to dsr on both plugs but not thru the cable
 
  • Like
Reactions: faruq

    F

    faruq

    Points: 2
    Helpful Answer Positive Rating
virtual terminal proteus

if you use two machines you need
a null serial cable {sometimes called a modem cable}
Click to expand...

actually I was wanting to run Proteus and Hyperterminal on the same machine.
My idea was to establish some sort of a virtual serial port connection between them.

to use hyperterminal you can also connect com 1 physical port to com2 physical port

set hypertermal to use only com 2
and the compim in isis only to use com1
Click to expand...

on same machine ?
 

proteus terminal

hi

Look at the reply above instead. The solution is there !

You need to replace Virtual Terminal with COMPIM (virtual COM interface). You must have 2 COMs free in your PC and a null modem cable (crossed).

Say you have COM1 and COM2 free. Connect the null modem between the two ports as a link and set COMPIM as the port COM1. Then use Windows Terminal (or whichever program you like) and set it as COM2. You'll see that any outputs that before were sent to the Virtual Terminal are now sent to Windows Terminal (or any other you may use).

Alternatively, if you don't have 2 physical COMs free then you may use some software driver, like Virtual Serial Ports Driver XP from https://www.eltima.com/products/vspdxp/
 
proteus virtual serial port

you hit the bull's eye.

just what i was wanting to do. But couldn't figure out how to do it.

Thanks, really.
 

proteus com port

No need to do the NULL MODEM if you have a VIRTUAL COM PORT PROGRAM..
I am using the software from Eltima software "VSPD XP 5.0"

https://www.eltima.com/
 

hyperterminal proteus

eYe said:
No need to do the NULL MODEM if you have a VIRTUAL COM PORT PROGRAM..
I am using the software from Eltima software "VSPD XP 5.0"

h**p://www.eltima.com/
Click to expand...

if you read the my post carefully this is already stated in my post that if you do not have com port you can used virtual port driver VSPD XP

regards
Fragrance
 

Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top