Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

[Question] WCDMA Bandwidth

Status
Not open for further replies.
currentmirror2000

currentmirror2000

Member level 4
Member level 4
Joined
Dec 21, 2004
Messages
77
Helped
6
Reputation
16
Reaction score
1
Trophy points
1,288
Activity points
798
channel spacing wcdma

hi all,

in WCDMA, the chip rate is 3.84MHz and the channel spacing is 5MHz

which one i should choose to use as bandwidth in order to calculate the noise figure? 3.84MHz or 5MHz?

thanks in advance!
 

channel bandwidth, dect

3.84MHz
 

    currentmirror2000

    currentmirror2000

    Points: 2
    Helpful Answer Positive Rating
    V

    Points: 2
    Helpful Answer Positive Rating
wcdma bandwidth chip rate

vfone said:
3.84MHz
Click to expand...

thank you, but why? how about GSM900, GSM1800 and DECT?

for GSM900/1800 and DECT, they have data rate and channel spacing, which one should be used as bandwidth? and why?
 

wcdma bandwith

The noise figure is measured by integrating noise power across the full-received signal bandwidth of 3.84 MHz using a matched filter.
3.84MHz is the channel Bandwidth and 5MHz is the channel spacing.
Receiver sensitivity according to 3GPP spec is measured in dBm/3.84MHz.
In GSM the channel Bandwidth is 180kHz and channel spacing is 200kHz.
 

    currentmirror2000

    currentmirror2000

    Points: 2
    Helpful Answer Positive Rating
    V

    Points: 2
    Helpful Answer Positive Rating
wcdma channel bandwidth 3.84mhz

vfone said:
The noise figure is measured by integrating noise power across the full-received signal bandwidth of 3.84 MHz using a matched filter.
3.84MHz is the channel Bandwidth and 5MHz is the channel spacing.
Receiver sensitivity according to 3GPP spec is measured in dBm/3.84MHz.
In GSM the channel Bandwidth is 180kHz and channel spacing is 200kHz.
Click to expand...

can i use the channel spacing as bandwidth to calculate noise figure in GSM if the channel bandwidth is not given.

btw, how about DECT? similar as GSM?

thanks!
 

gsm wcdma bandwidth compare

There are 0.5dB difference in Noise Floor between 180kHz and 200KHz BW.
For a Sensitivity measurement would be no big difference between these two BW because anyway you need another ~10dB margin to reduce the Noise Floor significantly below the required sensitivity level.

GSM required Noise Floor = -102dBm – 10LOG(180000) – 10 = -164.5dBm/Hz

DECT has the same story.
 
wcdma gsm noise floor

so you mean in GSM and DECT we can use the channel spacing as the bandwidth to calculate the noise figure approximately and in WCDMA we have to use the chip rate instead of the channel spacing as the bandwidth to calculate the noise figure. am i right?


in fact, i also have the data rate for WCDMA (+chip rate), GSM and DECT, what is this? why we cannot use the data rate as the bandwidth?
 

how is wcdma bandwidth calculated ?

For GSM/DECT you can use approximately the channel spacing for NF measurement, but I don’t understand why you don’t use the channel bandwidth, now when you know what is about.
In WCDMA (because is spread spectrum) the chip rate dictate the channel BW, and not the data rate.
 
channel bandwidth of gsm

vfone said:
For GSM/DECT you can use approximately the channel spacing for NF measurement, but I don’t understand why you don’t use the channel bandwidth, now when you know what is about.
In WCDMA (because is spread spectrum) the chip rate dictate the channel BW, and not the data rate.
Click to expand...

thank you very very much for your kind help!!!

to answer your question, it is simply because the channel bandwith is not given in the question/spec... only channle spacing and data rate are given for each case, in WCDMA chip rate is also given. so i was confused which to use :cry:

i think we can close this topic, thank you very much again
 

    V

    Points: 2
    Helpful Answer Positive Rating
Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top