Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

ldo shut down circuit?

M

mssong

Junior Member level 2
Junior Member level 2
Joined
Jul 25, 2023
Messages
22
Helped
0
Reputation
0
Reaction score
0
Trophy points
1
Visit site
Activity points
190
What circuitry or devices should I add to make LDOs shut-down?

The simplest means I can think of is to attach a MOS to the gate input of the PASS TR to force it high, but the leakage current will cause the gate node to take a different voltage than expected.

Is there a better way?

1724351007292.png
 
Sort by date Sort by votes
mssong said:
What circuitry or devices should I add to make LDOs shut-down?

The simplest means I can think of is to attach a MOS to the gate input of the PASS TR to force it high, but the leakage current will cause the gate node to take a different voltage than expected.

Is there a better way?

View attachment 193248
Click to expand...
What do you mean “take a different voltage…?
If your MOSFET pulls the gate close to the rail, leakage current will have a minimal effect. BUT, how will you drive that MOSFET’s gate?
 
Upvote 0 Downvote
One way is to contrive a memory cell of some kind. Rig it to detect excessively hi or low voltage. Thus causing it to change state. Apply its output (through a resistor, diode, capacitor, etc) to some vital component so that a change of state shuts down operation.

The memory effect maintains the shut down indefinitely. Without memory the system may oscillate between working and shut-down.
 
Upvote 0 Downvote
BradtheRad said:
One way is to contrive a memory cell of some kind. Rig it to detect excessively hi or low voltage. Thus causing it to change state. Apply its output (through a resistor, diode, capacitor, etc) to some vital component so that a change of state shuts down operation.

The memory effect maintains the shut down indefinitely. Without memory the system may oscillate between working and shut-down.
Click to expand...
Maybe I missed the point, but I think the OP’s question has nothing to do with detecting voltage, memory, etc. They were asking what circuit could implement the shutdown.
 
Upvote 0 Downvote
barry said:
Maybe I missed the point, but I think the OP’s question has nothing to do with detecting voltage, memory, etc. They were asking what circuit could implement the shutdown.
Click to expand...
Yes, that's right, you need an additional circuit just for the shutdown of the LDO.

If you design the circuit as shown below, the GATE NODE of PASS TR will be held close to HIGH even though OFF is HIGH.

So I thought this might be due to leakage current.

1724398744366.png

--- Updated ---

BradtheRad said:
One way is to contrive a memory cell of some kind. Rig it to detect excessively hi or low voltage. Thus causing it to change state. Apply its output (through a resistor, diode, capacitor, etc) to some vital component so that a change of state shuts down operation.

The memory effect maintains the shut down indefinitely. Without memory the system may oscillate between working and shut-down.
Click to expand...
Thanks, but I've never studied anything about memory, so I don't know what you're talking about. Could you explain it a bit more easily?
 
Upvote 0 Downvote
Hi @mssong

I am quite unsure that your gate leakage may be that significant... I should be in the order of tens-hundreds of nA, not more.
My guess would be that you probably not disabling your opamp properly and that's why you don't get what you expect. Make sure that all the gates of NMOS in your opamp are pulled low and all PMOS are pulled high, then try to pull the pass transistors' gate high and it should work.
--- Updated ---

mssong said:
If you design the circuit as shown below, the GATE NODE of PASS TR will be held close to HIGH even though OFF is HIGH.
Click to expand...
This is very confusing. What is the problem here exactly? The pass transistor gate (M22) cannot be pulled high to turn it off, or the opposite - M44 hold the gate of the pass transistor high even when it is open?
In any case, I believe that proper disabling of your opamp together with pass transistors' gate pull up should do the job.
 
Last edited:
Reply

    M

    mssong

    Points: 2
    Helpful Answer Positive Rating
Upvote 0 Downvote
Hi,

whatis the purpost of the shut down?
* just to switch OFF the output?
* or reducing the total power consumption to a minimum? --> then you should shut down the OP, too.

Klaus
 
Reply

    M

    mssong

    Points: 2
    Helpful Answer Positive Rating
Upvote 0 Downvote
sidun.av said:
Hi @mssong

I am quite unsure that your gate leakage may be that significant... I should be in the order of tens-hundreds of nA, not more.
My guess would be that you probably not disabling your opamp properly and that's why you don't get what you expect. Make sure that all the gates of NMOS in your opamp are pulled low and all PMOS are pulled high, then try to pull the pass transistors' gate high and it should work.
--- Updated ---


This is very confusing. What is the problem here exactly? The pass transistor gate (M22) cannot be pulled high to turn it off, or the opposite - M44 hold the gate of the pass transistor high even when it is open?
In any case, I believe that proper disabling of your opamp together with pass transistors' gate pull up should do the job.
Click to expand...
KlausST said:
Hi,

whatis the purpost of the shut down?
* just to switch OFF the output?
* or reducing the total power consumption to a minimum? --> then you should shut down the OP, too.

Klaus
Click to expand...
This is just to turn off the output.
 
Upvote 0 Downvote
mssong said:
This is just to turn off the output.
Click to expand...
If you don't want to turn off the opamp, you can add one more switch disconnecting the output of the opamp from the pass transistor gate simultaneously when pulling the gate of the pass transistor high. But I don't think this is a good approach.
 
Reply

    M

    mssong

    Points: 2
    Helpful Answer Positive Rating
Upvote 0 Downvote
mssong said:
This is just to turn off the output.
Click to expand...
If possible I´d keep the OPAMP in regulation (instead of saturation).
This could improve ON/OFF behaviour reagrding overshot, ringing and settling time.

Klaus
 
Reply

    M

    mssong

    Points: 2
    Helpful Answer Positive Rating
Upvote 0 Downvote
Jam the pass FET gate off, cut error amp power (because
you will have a standby current spec, will you not?), and
pull any soft-start / inrush limiter to its lowest value position.
Switches cost nothing, kill 'em all.
 
Upvote 0 Downvote
dick_freebird said:
Jam the pass FET gate off, cut error amp power (because
you will have a standby current spec, will you not?), and
pull any soft-start / inrush limiter to its lowest value position.
Switches cost nothing, kill 'em all.
Click to expand...
Switches cost nothing? Please send me 100000 of those free switches that you have.
 
Upvote 0 Downvote

LaTeX Commands Quick-Menu:

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top