Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

OP-Amp non linearity in verilog A model

Status
Not open for further replies.
C

Chinmaye

Full Member level 3
Full Member level 3
Joined
Jan 18, 2016
Messages
164
Helped
0
Reputation
0
Reaction score
1
Trophy points
1,298
Visit site
Activity points
3,145
Dear all,
I am trying to build a verilog A model of a differntial op-amp which gives an output of type
Vout = A.Vin + A3. Vin^3.

But I am quite unsure of how one can do this. Please help
 

Code: 
module opamp_nonlinear(in_p,in_n, out_p,out_n,vcm_out);
voltage in_p, in_n,out_p,out_n,vcm_out;
parameter real Rin = 50 from (0:inf];
parameter real Rout = 50 from (0:inf];
parameter real Gp_dB = 10 from [-100:100];
parameter real a2 = 0 from [0:inf];
parameter real IP1dB =0 from [-100:100];
real Gp=4*(10**(Gp_dB/10)); // The factor 4 is to account for the power loss in the input and output impedances.
real a1=((Gp*Rout)/Rin)**0.5;
real IP1dB_magnitude=(10**(IP1dB/10))*1e-3;
real Vin1dBc=(2*Rin* IP1dB_magnitude)**0.5;
real a3=(4*0.109*a1)/(3*(Vin1dBc**2));
analog begin
    V(out_p,vcm_out)<+ 0.5*(a1*V(in_p,in_n)+a2*(V(in_p,in_n)**2)-a3*(V(in_p,in_n)**3));
    V(out_n,vcm_out)<+ -0.5*(a1*V(in_p,in_n)+a2*(V(in_p,in_n)**2)-a3*(V(in_p,in_n)**3));
end
endmodule
 
Last edited by a moderator:
Thank you for the code. I could not understand the complete code. Here is a code I have for an diff input and diff output op-amp in verilog-A. How can i modify it to include non linearity in the code.
Code: 
`include "constants.vams"
`include "disciplines.vams"

`define PI      3.14159265358979323846264338327950288419716939937511

module diff_ampl(voutp,voutn, vin_p, vin_n, vspply_p, vspply_n, vcm );
input vin_p , vin_n , vcm;
inout vspply_p, vspply_n;
output voutp,voutn ;
electrical vin_p, vin_n, voutp, voutn, vspply_p, vspply_n, vcm;


parameter real gain = 400 exclude 0.0;
parameter real pole_freq =800000;
parameter real rin = 12.0M exclude 0.0;
parameter real rout = 10.0;
parameter real ibias = 0.0n;
parameter real vin_offset = 0.0u;


// parameter real slewp = 20.0M from (0:inf);
// parameter real slewn = -20.0M from (-inf:0);

real c1, r1;
real r_rout,gm_nom, vin_val;
electrical coutp, coutn, vref;


analog
begin

@(initial_step)// or initial_step("dc", "ac", "tran", "xf"))
begin
gm_nom = 0.01;
r1 = gain/gm_nom;
c1 = gm_nom/(`M_TWO_PI * pole_freq * gain);
r_rout = rout;

end

vin_val= V(vin_p, vin_n) + vin_offset;


// ------ Vref is at Virtual Ground

V(vref,vspply_n) <+ 0.5*V(vspply_p,vspply_n);



// ------ Input Stage

I(vin_p, vin_n) <+ vin_val / rin;
I(vref, vin_p) <+ ibias;
I(vref, vin_n) <+ ibias;



// ------ GM stage


I(vcm, coutp) <+ (gm_nom/2)*vin_val ;
I(vcm, coutn) <+ -(gm_nom/2)*vin_val ;



// ------ Dominant Pole.

I(coutp, vcm) <+c1*ddt(V(coutp, vcm));
I(coutp, vcm) <+ V(coutp, vcm)/r1;

I(coutn,vcm) <+ c1*ddt(V(coutn, vcm));
I(coutn, vcm) <+ V(coutn, vcm)/r1;




// ------ Output Stage.

I(vcm, voutp) <+ (V(coutp) - V(vcm))/r_rout;
I(voutp, vcm) <+ V(voutp, vcm)/r_rout;

I(vcm, voutn) <+ (V(coutn) - V(vcm))/r_rout;
I(voutn, vcm) <+ V(voutn, vcm)/r_rout;
   end
endmodule
ude non-linearity?
 

Chinmaye said:
Thank you for the code. I could not understand the complete code. Here is a code I have for an diff input and diff output op-amp in verilog-A. How can i modify it to include non linearity in the code.
Code: 
`include "constants.vams"
`include "disciplines.vams"

`define PI      3.14159265358979323846264338327950288419716939937511

module diff_ampl(voutp,voutn, vin_p, vin_n, vspply_p, vspply_n, vcm );
input vin_p , vin_n , vcm;
inout vspply_p, vspply_n;
output voutp,voutn ;
electrical vin_p, vin_n, voutp, voutn, vspply_p, vspply_n, vcm;


parameter real gain = 400 exclude 0.0;
parameter real pole_freq =800000;
parameter real rin = 12.0M exclude 0.0;
parameter real rout = 10.0;
parameter real ibias = 0.0n;
parameter real vin_offset = 0.0u;


// parameter real slewp = 20.0M from (0:inf);
// parameter real slewn = -20.0M from (-inf:0);

real c1, r1;
real r_rout,gm_nom, vin_val;
electrical coutp, coutn, vref;


analog
begin

@(initial_step)// or initial_step("dc", "ac", "tran", "xf"))
begin
gm_nom = 0.01;
r1 = gain/gm_nom;
c1 = gm_nom/(`M_TWO_PI * pole_freq * gain);
r_rout = rout;

end

vin_val= V(vin_p, vin_n) + vin_offset;


// ------ Vref is at Virtual Ground

V(vref,vspply_n) <+ 0.5*V(vspply_p,vspply_n);



// ------ Input Stage

I(vin_p, vin_n) <+ vin_val / rin;
I(vref, vin_p) <+ ibias;
I(vref, vin_n) <+ ibias;



// ------ GM stage


I(vcm, coutp) <+ (gm_nom/2)*vin_val ;
I(vcm, coutn) <+ -(gm_nom/2)*vin_val ;



// ------ Dominant Pole.

I(coutp, vcm) <+c1*ddt(V(coutp, vcm));
I(coutp, vcm) <+ V(coutp, vcm)/r1;

I(coutn,vcm) <+ c1*ddt(V(coutn, vcm));
I(coutn, vcm) <+ V(coutn, vcm)/r1;




// ------ Output Stage.

I(vcm, voutp) <+ (V(coutp) - V(vcm))/r_rout;
I(voutp, vcm) <+ V(voutp, vcm)/r_rout;

I(vcm, voutn) <+ (V(coutn) - V(vcm))/r_rout;
I(voutn, vcm) <+ V(voutn, vcm)/r_rout;
   end
endmodule
ude non-linearity?
Click to expand...

I am not going to edit your code for you. Sorry but that is not happening.
You need to find the parameters of the third order equation that describes the non-linear behavior. For that you would need the input 1dB compression point in terms of voltage. Once you have that, you can get the co-efficients of the third order polynomial. Once youhave that, your output voltage = f(input_voltage) where f is the third order polynomial.
 

Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top