Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

How to use duplicate mirror

Status
Not open for further replies.
R

rajarani

Junior Member level 3
Junior Member level 3
Joined
Aug 4, 2016
Messages
26
Helped
0
Reputation
0
Reaction score
0
Trophy points
1
Activity points
167
can anybody tell me how to draw this square shape using Duplicate mirror option?? FSR.jpg
 

You want to draw it using CST or HFSS?
As you have not mentioned the intended software to be used
 

It is bit confusing in HFSS as I do not know why they have hidden the commands under Edit, Draw and Modeler ribbons.
Anyways you can mirror it
Edit>Duplicate>Mirror
Edit>Arrange>Mirror
The only difference in two is that first command will duplicate the structure while second one will just mirror it.
 

My problem is i am not getting how to give the position values.
After using that duplicate option 1st we should select base position right? i have chosen that as the FSR end point position later we have to give the values for dx dy and dz right for that what values i should give??
i am giving the position values for that but it is not exactly 90degree, it is slightly changed i am not getting where i have done wrong
 



Have a look at the figure I think it should solve your issue.
Be sure that your base position and normal position have same non zero components as you are using mirror command which will keep sure the normality issue
 
Thank you:) can you tell me why the position changed from 70 to 1 on what basis you have made that??

- - - Updated - - -

for square shape i am asking can you set the plates adjacently and send an image it will be helpful for me. plz

- - - Updated - - -

Command DuplicateMirror
"Coordinate System" Global
"Base Position" "-46.5 ,49 ,0" mm "-46.5mm , 49mm , 0mm"
"Normal Position" "46.5 ,49 ,0" mm "46.5mm , 49mm , 0mm"


i am getting the image like this
Untitled.png
 



I am not sure if I got your problem correctly have a look.
I use the following command instead of mirror
Edit>Duplicate>Around Axis
As in this case you do not need mirror command
 

Can you tell me what values you have given for dx dy and dz for this around axis option.Here also we should give values na??

- - - Updated - - -

If i simply go for that option it is coming like this.HFSS.JPG

- - - Updated - - -

hai nomigoraya thank you so much i got that one...Thank you for your precious time
 

hai nomigoraya
Can u tell me how to check the beamwidth in HFSS
 

Please explain a bit about your problem
What is beam and what you want to measure
 

nomigoraya said:
Please explain a bit about your problem
What is beam and what you want to measure
Click to expand...

can please solve the boundary condition problem occured between perfE1&2 and rad1.
 

Attachments

  • Project7.rar
    26.6 KB · Views: 91

@sandeep if you explain your problem i will try to help you. my HFSS software is not working properly so
 

the following link shows the cpw fed patch antenna

**broken link removed**



these are the errors i am facing

**broken link removed**


please correct my erros
 

Increase the length and width of the radiation box
 

Hai sandeep check the attached image your problem is solved
Capture.JPG
 

Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top