Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Looking for software for capturing data/graph from VNA 8720B

Status
Not open for further replies.
G

greg12345

Junior Member level 3
Junior Member level 3
Joined
Nov 30, 2002
Messages
30
Helped
0
Reputation
0
Reaction score
0
Trophy points
1,286
Activity points
231
Hi
I'm looking for a software for capture data and graph from a 8720B network analyser.
I have the GPIB interface and I don't have time to write something under Labview.
I have tried intuilink (V1.2) and it doesn't work.

Could anybody help me??

Thank

Greg
 

agilent vee 8753

Try getting Agilent's VEE software...

They have virtual instruments (via GPIB) and ready-to-use drivers for HP8720 VNA... It will be a matter of 10minutes to acquire your data (even with no prior knowledge of the VEE environment)

mogwai.
 

    G

    greg12345

    Points: 2
    Helpful Answer Positive Rating
softplot free download

Thank Mogwai

Is it possible to make exe file with VEE by @gilent?

Good day

Greg
 

agilent uncerttest.xls

You can use SoftPlot V5.0
 

    G

    greg12345

    Points: 2
    Helpful Answer Positive Rating
uncerttest.xls agilent

SoftPlot or SPview are commercial but economic solutions.
Are you sure the problem is with intuilink?
If you have NI-Spy , you can monitoring the GPIB if data flow exist.
In any case, you should check the 8720 GPIB settings.
 

    G

    greg12345

    Points: 2
    Helpful Answer Positive Rating
retrieve data from vna software gpib

Hi Sergio

When I used intuilink (V1.2), I was able to check the VNA and when I tried to transfert data I had the message "PU not supported".

It is stange because normally the V1.2 is able to support this VNA (8720B).
I used GPIB/USB from NI and not from Agilent. Perhap's it's the problem!
Thank

Greg
 

gpib 8720d

For 8720B I am using in this moment Softplot.
 

    G

    greg12345

    Points: 2
    Helpful Answer Positive Rating
vector network analyzer 8722 price

greg12345 said:
Hi Sergio

When I used intuilink (V1.2), I was able to check the VNA and when I tried to transfert data I had the message "PU not supported".

It is stange because normally the V1.2 is able to support this VNA (8720B).
I used GPIB/USB from NI and not from @gilent. Perhap's it's the problem!
Thank

Greg
Click to expand...

Me too i have GIPB-USB-B from NI. and work!
I've now checked my intuilink and it support 872xD...and later

I suggest to check GPIB setting on 8720. My setting is NOT pass trough and NOT System controller. I've left the recomended GPIB address for VNA's (26)
 

    G

    greg12345

    Points: 2
    Helpful Answer Positive Rating
ni usb gpib settings for vna

Hi sergio

Tomorrow I will Check GPIB setting on my 8720B. I hope that it will be ok.

Can you tell me your version of Intuilink? I think it's V1.3 because V1.2 support 8720A/B/C.

I will inform you to my tests on VNA.

Thank

GREG
 

8753c intuilink

greg12345 said:
Hi sergio

Can you tell me your version of Intuilink? I think it's V1.3 because V1.2 support 8720A/B/C.
Click to expand...
My Intuilink is ver. 1.3.0.4 and explicitally say that the compatible VNA are 8719, 8720, 8722, 8753 version D, E, ES, ET.

When i use Intuilink i do the following operations:
1) click "Identify Instruments", and wait for a response. The leds on VNA blinks.
2) Then ckick on connect
3) Manually, i set-up the wanted display format (i.e. smithchart if i want s11)
4) Intuilink v.1.3 can download the 4 spar at time only for 87xxE ; but in conjunction with the 8722D that i have, only 2 spar (i.e. s11 and s22) may by donwloaded at time.

P.S. Have you checked if others System Controller (other than the PC) are alive on your IEEE-488 bus ? Only one (the PC) is permitted.
 

8720b labview

Hi Sergio

I have just found moment now to try your solution!! sorry
I downloaded the V1.3 of intuilink. When I want to connect my VNA, I have the message "8720B is not a supported instrument"

It's impossible to acquire any data.
What is your VNA (8720D)??

Have you any idea?

Regards

greg
 

8722 vna manual

greg12345 said:
Hi Sergio

I have just found moment now to try your solution!! sorry
I downloaded the V1.3 of intuilink. When I want to connect my VNA, I have the message "8720B is not a supported instrument"

It's impossible to acquire any data.
What is your VNA (8720D)??

Have you any idea?

Regards

greg
Click to expand...
Effectively, a carefully raed of the help file of the Intuilink, say that only last version of 872x family may communicate with intuilink.
I have 8722D and it's limitate to only 2 spar at time. Apparently only 872xE has full support.

Alternatively there are almost 2 commercial solutions.
SPview - Fully functional, very friendly and easy, also light (on the old V 1.42).
SoftPlot, also a very good software, just less friendly but more "industry standard".

If you are a VNA user, there are almost two related jobs that are often tedious to do:
1) Insert Cal Kit data into VNA
2) Calculate the measurement uncertainty

for both there are the relative free software.
1) www.vnahelp.com
2) search for "UncertTest.xls" on Agilent website
 

8720a intuilink

I had the same problem. For the graph part, the only thing I can
suggest is to get a Digital Camera and take a picture. It's not
sophisticated but it's easy.

Cheers
 

intuilink 8753

Hi
I have tested the eval version of SPview for make the capture of the data.
It work fine and the price is not expensive.
I think that it is a solution for the old VNA
You can download the eval version directly at :

https://www.arkrfsystems.com/downloads.htm

Regards

Greg
 

Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top