Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Wavelength and 300/f what is the deference ?

Status
Not open for further replies.
V

votientu

Member level 2
Member level 2
Joined
Oct 27, 2012
Messages
47
Helped
0
Reputation
0
Reaction score
0
Trophy points
1,286
Activity points
1,647
Hi everyone, I have a question about wavelength on transmission line,
According to Microwave Engineering Book of Pozar, \[\lambda\] = 2*pi / beta (2.10)
And beta is calculated from R,L,G,C on the transmission line.

Please check this link: https://www.emtalk.com/mscalc.php?e...ts_list=Wmm&La=8.21969195722&L_units_list=Lmm
Elec.length = 90 means this is mode quater wavelength, so it means wavelength is 8*4=32 mm, if I change the frequency to 2.4, I give the wavelength is 17*4=68 mm.

So, my question is if \[\lambda\] is dependent on beta, then what is the frequency for ?
Please help me, thank all of you !
 

The frequency is a measure of oscillating charges; it is defined by signal source.
Wave length is a parameter of electromagnetic wave with a given frequency, measured along the line of propagation. If the wave propagates in air or vacuum, the equation c = f. lambda is valid , where c is the speed of light in vacuum.
If you propagate the wave in another medium or in a transmission line, c is different by that medium (permittivity) and/or by the structure of the transmission line.
 
From the real model of transmission line it compose of inductor, capacitor whose Reactance changes with frequency which effects lambda..
 
Oki, I get it. Thank all of you !
 

300/f is a crude approximation to the real equation λ = C/f. C is the speed of light in whatever medium you happen to be in.
 
biff44 said:
300/f is a crude approximation to the real equation λ = C/f. C is the speed of light in whatever medium you happen to be in.
Click to expand...

actually 300/f is a quite accurate lambda in vacuum, where f is in Mhz and result is in Meters. It differs from the real value by less than 0.07%

The factor of 300 will vary quite a lot depending on which medium the EM is passing through, and in fact this ratio ( c / Vp) is called the the refractive index of that medium, which is always greater than 1, and in fact can be quite large for some materials. Alternatively it is the ratio of permitivity or permeability of the material to that of vacuum for opaque materials and electrical signals

In effect, both frequency and c are "hidden" inside the other parameters in the asker's refered equations.
 
Last edited:
So if the ratio c/Vp is constant for one medium, lamda is constant for one medium at one frequency beacause lamda = Vp/f (2.11 in Microwave Engineering of Pozar).
Please refer this link https://www.emtalk.com/mscalc.php?e...ts_list=Wmm&La=8.21969195722&L_units_list=Lmm and only change R to 60, you will give another lamda, lamda = L * 4 at mode quater wave length.
Please check for me !
Thanks!

- - - Updated - - -

So, it leads to the conclution that L is not equal to lamda/4. Why ? Electric length is 90, it is mode quater wave length, isn't it ?

I understand that lamda just depends on the medium the EM passes through and frequecy.
L at mode quater wave length will vary depending on Zo and of course lamda.
What do you think about it ?
 

Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top