Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Could you help me to correct this structure?

Status
Not open for further replies.
T

tw20053010

Member level 1
Member level 1
Joined
Oct 24, 2004
Messages
33
Helped
0
Reputation
0
Reaction score
0
Trophy points
1,286
Activity points
293
radiation pattern of 3λ

Dear Sir:

I am trying to simulate an patch antenna. But there are something wrong in defining waveport and boundaries. I have put it in the attachment. Could you help me to correct it? I need the result of E and H in the far field from 1GHz to12GHz.
My email: tw20053010@163.com
Thank you very much!


Regards,

Wei
 

tw20053010 said:
Dear Sir:

I am trying to simulate an fix antenna. But there are something wrong in defining waveport and boundaries. I have put it in the attachment. Could you help me to correct it? I need the result of E and H in the far field from 1GHz to12GHz.
My email: tw20053010@163.com
Thank you very much!


Regards,

Wei
Click to expand...

Try this one out
 

    T

    tw20053010

    Points: 2
    Helpful Answer Positive Rating
I have seen the structure, I think the boundary is not good.
The patch and ground should assign PerfE.
 

    T

    tw20053010

    Points: 2
    Helpful Answer Positive Rating
wlcsp said:
[
Try this one out
Click to expand...

My two cents:
Assume this antenna work at 10GHz, then the wavelength λ =3cm=30mm
the distance between your metal cap and the circular patch antenna is 20mm,
2/3 λ , I believe it will spoil the orignal radiation pattern.

So i prefer to remove the cap and reduce the size of radiation air box.

Even MoM require more dense meshing matrix, 1 wavelength λ 10segements should be enough, I checked your mesh refinement, maximum length you set is 1 mm, it means 1 wavelength 30segements, I think it is too strigent, no need to use such a fine mesh. And your model is too time and ram consuming.



btw, what is the radiation mechanism of this kind of antenna? there is no ground plane beneath the antenna, the radiation efficience should be very low, am I right?
another problem is the input impedance, is it possible to match it to normal 50 Ω ?

After my simulation finished, I will attach the results and keep u updated.

Best Regards,
 

    T

    tw20053010

    Points: 2
    Helpful Answer Positive Rating
asdfaaa said:
wlcsp said:
[
Try this one out
Click to expand...

My two cents:
Assume this antenna work at 10GHz, then the wavelength λ =3cm=30mm
the distance between your metal cap and the circular fix antenna is 20mm,
2/3 λ , I believe it will spoil the orignal radiation pattern.

So i prefer to remove the cap and reduce the size of radiation air box.

Even MoM require more dense meshing matrix, 1 wavelength λ 10segements should be enough, I checked your mesh refinement, maximum length you set is 1 mm, it means 1 wavelength 30segements, I think it is too strigent, no need to use such a fine mesh. And your model is too time and ram consuming.



btw, what is the radiation mechanism of this kind of antenna? there is no ground plane beneath the antenna, the radiation efficience should be very low, am I right?
another problem is the input impedance, is it possible to match it to normal 50 Ω ?

After my simulation finished, I will attach the results and keep u updated.

Best Regards,
Click to expand...

I just modified the model as the author wished for, by adding the pec cap. I do not know at all what he/she really wants to model.
 

    T

    tw20053010

    Points: 2
    Helpful Answer Positive Rating
Just got your message this morning, The attached figure is the simulation results, and I have send the whole porject file to you, It is really amazing that you using the same project file, but get such a different results. :( Did you change any setting to the project file I post here?

Please attach the project file you did the simulation here. Only s2p file, I cant get any information except the large discrepence of our simulation results.

Best Regards,
 

    T

    tw20053010

    Points: 2
    Helpful Answer Positive Rating
hi asdfaaa
i am new in hfss i have a question why he/she put a metalic box behind the waveport
can u send me the modified file about this project
thank u very much
 

Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top