Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by sudni

  1. S

    TNT decoder H.S : Metronic zapbox easy

    decoder tnt Hi all, my TNT decoder do not run!!! I verify power supply, but I'm not specialist of switched mode power supply. In connector I found : 3,4V, 5V, 12V, 32V but in the out 23V (22V) i found 0V! that all for the moment. I need help to repair my decoder I search schematic or all...
  2. S

    Problem with my Lcd Monitor for PC: Hyundai X90W

    hyundai x90w hi all, my lcd monitor have big problem : When I start on my monitor the third hight part of my screen is fuzzy. After a time (~ 30-60s) the screen is better is not perfect. When I move my mouse, the cursor disappears same as behind fog. I attached photo to show my problem...
  3. S

    how to design a 13.56MHz mifare contactless card reader

    Good job a this page : https://www.openpcd.org/ Very complete and clear Paul.
  4. S

    SD memory always in write protect

    Hi all, my daughter broke the memory board of her camera. Small the switch of Write protect was lost and now one cannot write any more above. Does somebody have to you it a schematic of this type of memory? How to force the writing of the memory ? Transcend SD 64 MB Thanks in advance for...
  5. S

    How to develop an application in embedded using MISRA C rules?

    I all, I search all documents to explain how to develop an application in embeded environment, and respect MISRA C rules. Thanks in advance for your hep, Paul.
  6. S

    Suggest me a cheap ARM evaluation board and IDE

    Re: ARM Newbie Sorry for the bad link, try this one http://vba.ngemu.com/ To purchase development tools I use this shop : **broken link removed** or this shop for french user http://www.ominfo.com/ Sudni.
  7. S

    Suggest me a cheap ARM evaluation board and IDE

    buy lpc-mt-2106 I interrested by ARM technologie, but I'm not rich and I prefer discover this architecture with just an small console : Gameboy Advance. With this console you all to discovers this component, and it's very easy to develop an application. Visual HAM it's a perfect IDE and very...
  8. S

    dsPic 30F2010 and circuit to learn this product

    30f2010 I all, I receive my DsPIc, and now i search a schematic or circuit to built a board to discover all possiblity of this product. Do you know web page or just file to explain how to use this dsp?? thanks in advance, sudni
  9. S

    MSComm Control for RS-232

    mscomm serial port Hi, for the com port on PC's goto a good html page. @+
  10. S

    do you known this µC ST90R30 ZC6R

    8O Hi all, I found an old µC card to command motor in machinetool; And I search all info on this µC ST90R30 ZC6R (datasheet, dev tools) Thanks in advance sudni
  11. S

    I search a good eprom/EEPROM professionnal programmer

    I see an ART EEP4 via USB, do you known this product??? thx in advancesudni
  12. S

    JDM programmer problem?

    I've the same problem on my pc prtoable, and is Vpp problem, just 10V in my case. On desk Pc I found 13,2 V. sudni
  13. S

    I search a good eprom/EEPROM professionnal programmer

    Hi all, I need a good eprom/EEPROM professionnal programmer, and connect to the PC by USB port. Do you a product or brand ?? thanks in advance for your experiences and help. sudni
  14. S

    PROTEUs 5.2 SP7 and serial or other PC port

    proteus 5.2 Hi all, I discover PROTEUS, and after worked with this marvelous software, one question run in my mind : Is possible in case of project with µcontroleur to send or receive data or signal via serial or parrallel port ? Thanks in advance for your help.
  15. S

    Need help: Need datasheet or info on LCD screen of NOKIA510

    datasheet for lcd mobile phones just to signal an error in title, I search all information to use the LCD in first time , same as console by the way of serial/paralell port; in second time to interface with the PIC thanks.
See more

Part and Inventory Search

Back
Top