Continue to Site

std_match's latest activity

S

std_match replied to the thread Cap on bias nets of current mirror.

The gate-source voltage is regulating the current. If the source is connected to Vdd (as in your circuit) and you filter to ground...

Mar 7, 2025
S

std_match replied to the thread [SOLVED] Issue with Contactor Driver Circuit – MOSFET Burns at Higher Voltage.

Have you measured that? I have 2 different brands of diff-probes which can handle about 1000V. If I remember correctly, one has 2 MOhm...

Mar 7, 2025
S

std_match replied to the thread [SOLVED] Issue with Contactor Driver Circuit – MOSFET Burns at Higher Voltage.

You mean a differential probe? It is good to know that most differential probes are not isolated. They normally have a few MegaOhms from...

Mar 6, 2025
S

std_match replied to the thread [SOLVED] Issue with Contactor Driver Circuit – MOSFET Burns at Higher Voltage.

Connect the clamp diode directly on the contactor terminals. If the MOSFET survives, the problem is related to the clamp diode wiring...

Feb 28, 2025
S

std_match reacted to rahuljnvlsi's post in the thread [SOLVED] 100% success for CDC circuit or not? with Like.

you can not guaranteed if your design is 100% CDC clen , you will not get any failure because of it. MTBF , can not be zero , although...

Feb 28, 2025
S

std_match reacted to dpaul's post in the thread [SOLVED] 100% success for CDC circuit or not? with Like.

Yes it is difficult to achieve the probability of failure to be 0. By very nicely synchronizing your design you just can reduce the...

Feb 26, 2025
S

std_match replied to the thread 2 unit communication with Multi Gigabit Transceiver via SFP connector.

Make sure that you have the GTY rx equalizer in "LPM" mode, not "DFE". Use software ADIsimCLK to design/verify the AD9528 PLL loop...

Feb 26, 2025
S

std_match replied to the thread Do While loop not working..

What is the maximum value for duty? It is returned by the PWMx_Mc_Init function. How long does it take for the green LED to go to 100%...

Feb 20, 2025
S

std_match replied to the thread Crystal load capacitor.

You use the same package as the majority of your other low power components. Today that is probably 0402 or 0603.

Feb 18, 2025
S

std_match replied to the thread LED Driver LM3409.

Vcst is at the top of the figure, next to the CSP pin, and it isn't referenced to ground. It is the offset/reference for the upper...

Feb 18, 2025
S

std_match replied to the thread measure a mosfet gate with a digital multimeter.

With a standard multimeter it should be an open circuit. Is something else connected to the gate in the circuit? Do you touch the probes...

Feb 17, 2025
S

std_match replied to the thread I think i have devised a new type of "super_transformer" for the Electricity grid?.

1. Your "super_transformer" can only maintain sinusoidal current up to the first branch of the connected grid. 2. I don't think...

Feb 17, 2025
S

std_match reacted to ThisIsNotSam's post in the thread calculate approximately maximum clock frequency with TNS. with Like.

TNS is not helpful because it can come from 1 path, 2 paths, 300 paths. WNS itself is not the most helpful either, you would have to...

Feb 14, 2025
S

std_match reacted to Hayk D's post in the thread [mark as solved] button with Like.

@std_match It makes sense. The auto closing of the thread when it is marked as solved is disabled. Thank you.

Feb 11, 2025
S

std_match replied to the thread [mark as solved] button.

I think it is bad if comments can't be added to a "solved" thread.

Feb 11, 2025

Show older items

Part and Inventory Search

This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.

Accept Learn more…

Top