Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
Can someone tell me what does one mean, when it is stated, "Some IC has "weak" pierce oscillators"?
What is the actually meaning when it one says a "weak pierce oscillator"?
Also, why is this configuration preferred when the pierce oscillator is weak?
What does this bias current do ? Does it...
In this datasheet: https://ww1.microchip.com/downloads/aemDocuments/documents/MPU32/ProductDocuments/DataSheets/SAMA5D2-Series-Datasheet-ds60001476.pdf
I'd like to understand the difference between the functions of pins mentioned below:
What is the difference between LCD Data enable vs LCD...
RTS5487 and RTS5413D are the parts which I would like to get the datasheet.
Unfortunately, I am unable to find the datasheet.
However, these parts are available in 3-party websites.
RTS5487...
I have a question.
Does the size of an MLCC 0201 capacitor when compared to 0603 MLCC capacitor of the same value have produce different effects on ripple voltage?
Like, does the size of the capacitor (0201 vs 0603) have any impact on the ripple voltage of a power rail?
When setting KSZ9131RNX to Remote Loopback, in addition to the register settings, there is a description that says "Connect RX_CLK to TX_CLK".
Q1.Does this mean physically connecting Pin to Pin?
Q2.If the above is correct, there are no pins named RX_CLK and TX_CLK, but does RX_CLK mean...
I read that the slew rate of an op-amp the rate at which the output voltage changes with time with respect to a step change in input.
So my question is will the slew rate of an op-amp depend on external circuit components?
Suppose,
1. I have a capacitor at the output of an op-amp. In this...
In this Ethernet PHY datasheet (https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/DataSheets/LAN8720A-LAN8720Ai-Data-Sheet-DS00002165.pdf), page 14, Figure 3-1, I see the blocks 4b5b encoding, NRZI and MLT-3.
I was reading about line coding and it's purpose.
One...
In this Application note recommendation for ground connection of the thermal ground pad of an IC on page 3,
(https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ApplicationNotes/ApplicationNotes/AN18.15-PCB-Design-Guide-QFN-DQFN-Packages-00001843.pdf),
I see that the ground paddle...
There's this MOSFET (https://mm.digikey.com/Volume0/opasdata/d220001/medias/docus/414/SH8K5.pdf)
The gate threshold range for this MOSFET is given as 1V to 2.5V from the table (but from the table I see this value is for a drain current of only 1mA).
My question is, I want to get a drive...
I am using a scope that has two termination inputs. 1Mohm and 50ohms internal termination on the probe inputs.
My question is :
1. Suppose I connect the probe to a USB differentia signal. I connect only 1 probe to D+. The ground of the probe is connected to the ground. Which termination scope...
This is a really helpful answer for me. Thank you very much. The example you gave is for a node right.
In my question, we have two nodes. A and B (from the Figure 2 in the above image). In that case, the equivalent parallel resistance of the two RBs, will be placed across RT2, I understand...
I was going through the biasing resistor calculation for RS-485 and can across this AppNote (https://www.renesas.com/us/en/document/apn/an1986-external-fail-safe-biasing-rs-485-networks).
On page 3, you can see below:
I just want to understand how the 2 RB resistors are considered to be in...
I have been going through the TNCS electrical system of grounding and noticed that this system has Multiple earths in the PEN conductor.
Refering to this link
However, I am not able to understand the purpose of the multiple earths. What is the purpose of it and how does multiple earth help in...
I am reading about the Electric Vehicle and their charging.
I went through this link - J1772, where the connector image is displayed.
The connector has a PE terminal.
Going through a lot of material and links, I read that the Protective Earth is connected to a earth rod on the charging...
Oh thanks.
1. When you mention TXxx pins are output but have an input arrow, you mean the black arrow, right?
2. Also, Rx pins of KSZ9567 is connected to Rx pins of LAN8840. But in the datasheet of both devices, Rx pins are mentioned as output.
LAN8840 datasheet:
KSZ9567 Datasheet:
But...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.