Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by abuzarshaikh7

  1. A

    Need Help with tda2009

    Hello , I have made the circuit as depicted in the data sheet for bridge mode what i observe is there is lot of unwanted noise after incresing the input to more than a certain level how do i reduce this also how to measure the output voltage and current of the tda2009a i tried with...
  2. A

    Need Help with tda2009

    thank you so much for the second link was really very help ful - - - Updated - - - thank you so much for the second link was really very help ful
  3. A

    Need Help with tda2009

    can any body tell me how much db can 10 watt output generate if i connect it to a 4 ohm 50 watt rated speaker - - - Updated - - - will this rating run all the four tda2009 how much current does one tda2009 rquire
  4. A

    Need Help with tda2009

    i want to use 4 of these tda2009 for that how can i design the system i need help with that what should be the current rating of transformer
  5. A

    Need Help with tda2009

    Hello i am making a project in which i will need four speakers so i need four amplifiers.... i wrked with tda2822 but it gave be only one watt nd -20 db sound at the source i need atleast 0 db sound so i asume that 10 watt will be required i am planning to use tda2009 as its output power...
  6. A

    bldc motor with avr for d quadcopter

    yes i usd laptop's hyperterminal. . I'l display on youtube when i m done. . I'l advance it to make it autonomus
  7. A

    bldc motor with avr for d quadcopter

    yeah i am that same person i have almost completed it.
  8. A

    bldc motor for quadracopter

    hey guys my brush less dc motor is working fine now.Just remember to first do the testing on servo motor.if the code works fine on servo motor then its surely going to work on brush less dc motor.:-D:-D
  9. A

    bldc motor with avr for d quadcopter

    hey there... i m making a quad copter..i have got brush less dc motors with Electronic Speed Controller...i am not using remote control..instead i m going for atmega16..but i m not getting how to give d signals to d motor...please help me for d coding n what else is needed for driving the...
  10. A

    bldc motor

    hey dere....ny body who can hlp me for programming a brushless dc motor??i m using it in my quadcopter...actualy i hv nvr used dis mtor b4..can nybdy hlp me for dis? i want to progrm it using avr microcontroller... plllzzz help.:-|:-|
  11. A

    request: Available AVR's in your area with cost per chip

    Atmega16pu(dip).....160 rs lamington road mumbai contact me at abuzarshaikh7@gmail.com
  12. A

    mma7455l interfacing with atmega16 spi

    Plzzz any bodyy helppp
  13. A

    mma7455l interfacing with atmega16 spi connection

    The problem is there are 3 pins in accelemeter mma7455 1.SDA 2.SD0 3.SCK And three pins on the avr atmega16 1. MOSI 2. MISO 3. SCK I want to know which pin of mma7455 should be connected to which pin of avr.
  14. A

    mma7455l interfacing with atmega16 spi

    I have written the code as below. The output is continuously zero. please help for errors in the code. thank you#include<avr/io.h> #include<util/delay.h> #include<stdio.h> ///////////////////// #define CE 4 //CHIP ENABLE #define MOSI 5 // SDA/SDI #define MISO 6 //SDO #define SCK 7 //SERIAL...
  15. A

    Shannon fano coding with MATLAB,

    u can simply use the google language conver tool to simply cont the explained language
See more

Part and Inventory Search

Back
Top